Contact Us

LTM8045EY#PBF

Brand: Analog Devices
Analog Devices LTM8045EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8045EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8045EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8045EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8045EY: the inverting or SEPIC module with a guarantee from zero degrees

The LTM8045EY#PBF is the commercial grade of the single output SEPIC and inverting module: 2.8 V to 18 V in, plus or minus 2.5 V to 15 V out, 700 mA at 2.5 V from a 12 V input, 200 kHz to 2 MHz switching, in an 11.25 mm by 6.25 mm by 4.92 mm ball grid array. The converter, both inductors and the control loop are inside, so an analogue board that needs a negative rail adds one part and two capacitors rather than a controller, an inductor pair and a feedback network. Its limits are guaranteed from 0 to +125 degrees internal.

Published values

ParameterValue
Input range2.8 V to 18 V
Output rangeplus or minus 2.5 V to plus or minus 15 V
Output current700 mA at 2.5 V; 375 mA at 15 V
Switching frequency200 kHz to 2 MHz, one resistor
Feedback reference1.215 V positive, 5 mV negative
Guaranteed range0 to +125 degrees internal; -40 assured by characterisation
Output ripple4 mV RMS at 5 V and 580 mA
Quiescent current10 mA not switching, 1 microamp shut down
Load regulation0.2 percent
Thermal28.7 degrees per watt to ambient, 10.5 to the board
Package40 lead BGA, 11.25 mm by 6.25 mm by 4.92 mm, MSL 3, 0.9 g
Synccan be locked to an external clock from 200 kHz to 2 MHz

A negative rail for an amplifier, without a second switcher

Operational amplifier stages that swing around zero need a rail below the signal return, and the usual answer is a charge pump with limited current or an inverting controller with an external inductor pair. This module replaces both: one part makes -5 V or -12 V at a few hundred milliamps, with 4 mV RMS of ripple, which is quiet enough that a following RC filter is enough for most analogue sections.

The thermal limit is what decides the current at 12 V and 15 V, not the magnetics inside the module. At an 85 degree ambient the 28.7 degrees per watt path allows 1.39 W of loss, so a 12 V rail at 375 mA is 4.5 W out and needs 76 percent efficiency to stay inside, while a 2.5 V rail at 700 mA needs only 56 percent. The converter clears both, but only the low voltage point has real margin.

The commercial grade in a mains powered instrument

An instrument that runs from a wall adapter is started in a room and stays there. The E grade is fully specified over 0 to 125 degrees, which covers that envelope with a wide margin, and the part behaves identically to the industrial code above freezing. The only cost is the missing guarantee below zero, which such a product never exercises.

The place this becomes a decision rather than a default is a portable instrument that might be left in a vehicle overnight. Storing at -20 is fine, since the storage rating is -55, but switching on at -20 is outside the E grade. If the product specification allows that, the industrial code is the correct order line.

Synchronising it, and why that matters on an analogue board

The SYNC pin accepts an external clock between 200 kHz and 2 MHz, so the converter can be locked to the system clock and its harmonics land at known frequencies instead of drifting with temperature and load. On a board with a 16 bit converter running at a fixed rate, that is often the difference between a spurious tone that moves and one that can be filtered.

The soft start pin sets the ramp, which matters when the negative rail feeds a large decoupling bank: without a controlled ramp the input supply sees the inrush as a short and either current limits or drops. The pin sources 8 microamps, so the ramp time is set by one capacitor and is predictable.

The pages that answer this most often are OEM procurement for the family alternatives, the power management cross reference for the acceptance test, and vendor consolidation for the case where a replacement has to be fitted before the next build.

Two questions buyers ask about the SEPIC module

Is the E grade interchangeable with the I grade on the same board? Electrically yes, same package and pin out. Below 0 degrees the guarantee does not apply, so a product specified to start cold needs the industrial code or an engineering sign off.

How much current can it deliver at minus 12 V? About 375 mA from a 12 V input, which is the 15 V point on the curve. The current falls as the magnitude rises, so the load has to be sized from the curve for the actual input and output rather than from the 700 mA headline.