Contact Us

LTM8033EV#PBF

Brand: Analog Devices
Analog Devices LTM8033EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8033EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8033EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8033EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8033EV: the low profile 3 A EMC module for a board that is short of height

The LTM8033EV#PBF is the commercial grade in the land grid array body, 11.25 mm by 15 mm by 4.32 mm with gold pads and the e4 finish. Inside is the same 36 V, 3 A converter with a 0.8 V to 24 V output range, 200 kHz to 2.4 MHz switching and 5 mV RMS of ripple, built against the radiated requirement of EN55022 Class B. The 4.32 mm height is 0.6 mm lower than the ball grid array version, which on a stacked board is often the whole reason this code exists.

Published values

ParameterValue
Input range3.6 V to 36 V
Output range0.8 V to 24 V
Output current3 A
Switching frequency200 kHz to 2.4 MHz, one resistor
Reference790 mV at ADJ
Quiescent current30 microamps not switching, 0.01 microamp shut down
Output ripple5 mV RMS
Line and load regulation0.3 percent and 0.4 percent
Emissionsradiated to EN55022 Class B
Power good730 mV rising threshold, 200 microamps of sink
Thermal15.4 degrees per watt to ambient, 5.2 to the board
Package76 pad LGA, 11.25 mm by 15 mm by 4.32 mm, MSL 3, 2.2 g
Guaranteed range0 to +125 degrees internal

Height is a mechanical decision with an electrical consequence

Reducing the standoff from 4.92 mm to 4.32 mm moves the module closer to the board, which shortens the thermal path into the copper and puts the top of the part under whatever sits above it. Both are usually good: the heat leaves through the pads anyway, and the lid of the enclosure is a poor heat path at 16.7 degrees per watt to the top.

What changes is the assembly window. A land grid array has no balls to collapse, so the joint height is the stencil thickness and the paste volume. A board that was qualified with the ball grid array part needs a new stencil, a new profile and a new inspection method before the land grid array code can be run on the same line.

Startup, bias and the pins that decide whether it works

The RUN/SS pin doubles as the soft start and the enable, with a 2.5 V input high threshold and a 0.2 V input low threshold, so it can be driven from logic or from a divider. The BIAS pin needs 2.8 V for proper operation and can be tied to the output to cut internal dissipation, which is worth doing on a 24 V input where the internal housekeeping current matters most.

The power good output trips at 730 mV on the ADJ pin as the output rises, so it is referenced to the reference rather than to an absolute voltage, and it sinks 200 microamps. That is enough for a logic input with a pull-up and not enough for a relay, which is the sort of detail that shows up as a marginal reset line rather than as a converter fault.

Where the 24 V output actually holds

The top of the output range is reached with a 16.5 k resistor from a 32 V input, and the current at that point is not 3 A. At an 85 degree ambient the 2.6 W budget would require 96.5 percent efficiency for 3 A at 24 V, which no converter of this size reaches, so the load has to be derated toward the top of the range.

The middle of the range is comfortable: 3 A at 5 V needs 85 percent and 3 A at 12 V needs 93 percent, both inside the converter's capability on a board that meets the published thermal number. A quote for a 24 V rail at 3 A should be checked against the derating curves before it is confirmed.

Buyers usually arrive at component lead time solutions to find the family alternatives, then use the power management cross reference to confirm a substitute before it is fitted; OEM procurement is the routine for a part that has already stopped shipping.

Two questions buyers ask about the low profile code

How much lower is this than the ball grid array version? 4.32 mm against 4.92 mm, so 0.6 mm. The footprint is the same 11.25 mm by 15 mm and the electrical behaviour is identical.

Is the land grid array harder to inspect? Yes. There are no visible balls, so inspection relies on pad wetting at the edge, X-ray for voids or a pull test on a coupon. That is a process cost to plan for, not a reason to avoid the package.