Contact Us

LTM8026IY#PBF

Brand: Analog Devices
Analog Devices LTM8026IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8026IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8026IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8026IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8026IY#PBF: the 5 A rating sits 0.6 A under the current limit

The LTM8026IY#PBF is the I grade of the 36 V, 5 A constant-current module in an 11.25 mm by 15 mm by 3.42 mm ball grid array with SAC305 balls and MSL 3. It runs from 6 V to 36 V in, 1.2 V to 24 V out, and both the voltage and the current loop are fully specified, so the part can be used as a charger rather than only as a rail. The I grade is -40 C to 125 C at the junction, the same window as the E grade in this family.

Published values

ParameterValue
Input voltage6 V to 36 V
Output voltage1.2 V to 24 V, RADJ = 11.9 / (VOUT - 1.19) in kohm
Rated output current5 A
Current limit at CTL_I = 1.5 V5.6 A typical, 5.1 A to 6.1 A
Output ripple10 mV RMS at 12 V in and 4.5 A
Load regulation0.7 percent from 0 A to 5 A
Line regulation0.1 percent from 6 V to 36 V
Junction to ambient18.6 C/W, 5.4 C/W to case bottom
Package11.25 mm x 15 mm x 3.42 mm BGA, MSL 3
Temperature range-40 C to 125 C, I grade

Where the 5 A stops and the limit starts

The rating and the protection threshold are not the same number. The output is specified to 5 A, and the current limit sits at 5.6 A typical with a 5.1 A to 6.1 A spread when CTL_I is at 1.5 V. Driving CTL_I to 1.34 V sets the limit to 5 A through the 2 V reference, which leaves the part with no margin over its own specification and a worst case limit of 4.55 A on a slow part.

In practice the 5 A rail is set with the limit at 5.6 A and the load is kept below 4.5 A, which is a 20 percent margin and the arrangement that survives a production spread. Boards that run the module at exactly 5 A and expect the limit to be a metrology point come back with units that trip early at the cold end, because the limit accuracy of 5 percent is quoted at 25 C rather than over the whole grade.

Ripple, and what the output capacitor is doing

Output ripple is published as 10 mV RMS at 12 V in and 4.5 A, which is small for a 5 A supply and is the reason some boards get away with fewer output capacitors than they expect. The number assumes the recommended 100 uF ceramic plus the bulk electrolytic in the component table, and removing the electrolytic to save height raises the ripple and degrades the transient in a way the headline figure does not show.

Load regulation is 0.7 percent across the full 5 A step, which is 35 mV on a 5 V rail and 8.4 mV on a 1.2 V rail in absolute terms. For a load that sees the rail as a reference rather than as a supply, that 0.7 percent is the number to hold the rail to, not the line regulation figure that looks ten times better.

The 3.42 mm body and the via field

The BGA stands 3.42 mm tall and has 18.6 C/W junction to ambient with 5.4 C/W to the case bottom. The gap between those two numbers is the board: a package on a four layer board with a via field under the thermal pads reaches the bottom figure, and a package on a two layer board with no vias sits near the top one.

At 36 V to 5 V and 5 A the output is 25 W and 90 percent puts 2.78 W in the package, which is a 51.7 C rise and about 73 C of ambient at a 125 C junction. Taking the 5.4 C/W path instead of 18.6 C/W moves the same loss to a 15 C rise, so the copper under the module is worth more than any change of grade.

Ordering the I grade, and when it is the wrong code

LTM8026EV, LTM8026IV, LTM8026EY and LTM8026IY are all -40 C to 125 C. Only the MP codes move to -55 C. A buyer who asks for the I part to get a wider window is buying the same window with a different label, and the approved vendor list is the only reason to hold both.

The real choice in this family is the body: LGA at 2.82 mm with Au pads, or BGA at 3.42 mm with SAC305 balls. Those two are not interchangeable on a built board, so the body should be fixed before the first prototype rather than after the thermal test.

Where a customer needs a second position on this part, the power management cross reference is the starting point, component lead time solutions sets out the checks a substitution has to pass, and vendor consolidation is the short lead time route we quote against.

Two questions buyers ask

Is a 5 A load safe with CTL_I at 1.5 V? It runs at 5.6 A typical and up to 6.1 A, so the load is inside the rating but outside the margin. Set CTL_I to 1.34 V for a 5 A limit and keep the load below 4.5 A if the rail has to hold across temperature.

Does the module need an external current sense resistor? No. The current loop uses the inductor and switch current inside the package. The setpoint is a voltage on CTL_I, a resistor, or a thermistor, and none of those carries the load current.