Contact Us

LTM8026EV#PBF

Brand: Analog Devices
Analog Devices LTM8026EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8026EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8026EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8026EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8026EV#PBF: using the current loop for LED strings and battery packs

The LTM8026EV#PBF is the E grade, Au pad, land grid array body of the 36 V, 5 A constant-current module, 11.25 mm by 15 mm by 2.82 mm, MSL 3. Its distinguishing feature inside the family is that the primary loop can regulate current, and the setpoint can come from a voltage, a resistor or a thermistor on CTL_T. That makes it a candidate for LED drive and for charging, not only for a fixed rail.

Published values

ParameterValue
Input voltage6 V to 36 V
Output voltage1.2 V to 24 V
Output currentup to 5 A, set by CTL_I or CTL_T
Reference for dividers2 V at VREF
Current limit spread5.1 A to 6.1 A at CTL_I = 1.5 V
Thermistor inputCTL_T, same limit behaviour as CTL_I
Junction to ambient18.6 C/W, 5.4 C/W to case bottom
Package11.25 mm x 15 mm x 2.82 mm LGA, Au pads, MSL 3
Temperature range-40 C to 125 C, E grade
Parallel operationVIN, VOUT and share pins tied

Setting a current with a divider instead of a controller

The 2 V reference at VREF exists so that a two resistor divider can set the current without a housekeeping controller. For a 4 A setpoint the divider has to put 4 A x 5.6 A / 5 A worth of control voltage on CTL_I, which is about 1.07 V, and a 66.5 k with a 140 k from the reference gives 1.35 V and a 4.8 A setpoint on the vendor's own numbers.

The tolerance of that divider adds directly to the current tolerance, and a 1 percent pair is worth the extra cent on a production board. Where the setpoint has to be trimmed, a small digital pot or a PWM filtered node on CTL_I is the usual route, and the module does not care which of those it sees.

An LED string on a current loop

A string of white LEDs at 3.2 V each and 1 A is a 32 V load, and this module tops out at 24 V out, so the string length is the first limit. Six LEDs at 3.2 V is 19.2 V, which leaves 4.8 V of headroom under the ceiling and 1 A of current regulation inside the 5 A rating, so a 36 V bus driving a 6 LED string at 1 A is the arrangement that fits.

PWM dimming is done on the current setpoint and not on the output, because switching the rail on and off at 5 A is what the soft start is there to slow down. At 1 kHz PWM the module sees a 1 ms step every cycle and the current loop settles in tens of microseconds, so the visible flicker is set by the output capacitor and not by the loop.

Charging, and the thermistor path

CTL_T accepts a thermistor so that the charge current falls as the cell warms, which is the behaviour a lithium pack needs and a fixed resistor cannot give. The same pin can be driven from a divider if the temperature qualification is done elsewhere, and the module then behaves like a plain current source with a limit.

The input current is again the sizing constraint. A 2.5 V 100 F supercap charged at 5 A takes 50 seconds and draws 5 A x 2.5 V / 6 V of input, about 2.1 A plus loss, from a 6 V rail. At the end of the charge the input current falls away with the load, so the feed has to be sized for the start of the charge and not for the average.

What a 5 A module does not protect

The current loop protects the module and the load from overcurrent, and it does not protect the load from the module. A shorted LED string under current regulation is a setpoint, and the module will hold it until the thermal path gives up or something else opens the circuit.

Reverse polarity on the input is also outside the part. The 36 V rating is a forward operating window, and a reversed bus puts the body diode and the input capacitor in the path. A series Schottky or an ideal diode in front of VIN is standard practice here, and its forward drop is part of the input range arithmetic on a 6 V minimum bus.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, how to reduce component cost is the check list before a substitute goes in, and one stop BOM sourcing is how a gap is covered without a new line item.

Two questions buyers ask

Can the module drive an LED string at 24 V? Yes, up to 24 V out, which is about seven white LEDs in series at 3.3 V. Above that the string has to be split or a boost topology is needed, and this family is a step-down only.

Is PWM dimming done on the rail or on the setpoint? On the setpoint. The current loop follows a PWM signal on CTL_I within tens of microseconds, and switching the rail itself at 5 A is limited by the soft start rather than by the loop.