Contact Us

LTM8025IY#PBF

Brand: Analog Devices
Analog Devices LTM8025IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8025IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8025IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8025IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8025IY#PBF: 36 V in, 5 V out and the frequency table that decides on time

The LTM8025IY#PBF is the I grade of the 36 V, 3 A step-down module in a 9 mm by 15 mm by 4.92 mm ball grid array with SAC305 balls and MSL 3. Input range is 3.6 V to 36 V, output range is 0.8 V to 24 V, and the switching frequency spans 200 kHz to 2.4 MHz, which is wider than the rest of this family and is what makes a small output capacitor possible. The I grade is -40 C to 125 C at the junction.

Published values

ParameterValue
Input voltage3.6 V to 36 V
Output voltage0.8 V to 24 V, ADJ pin at 790 mV
Output current3 A
RT for 200 kHz215 k
RT for 400 kHz100 k
RT for 1 MHz34.0 k
RT for 1.8 MHz14.7 k
Junction to ambient24.4 C/W, 11.5 C/W to case bottom
Package9 mm x 15 mm x 4.92 mm BGA, MSL 3
Temperature range-40 C to 125 C, I grade

The frequency table is really an on-time table

The vendor publishes RT against switching frequency rather than a minimum on time: 215 k gives 200 kHz, 100 k gives 400 kHz, 34.0 k gives 1 MHz and 14.7 k gives 1.8 MHz. Those values are what a specification should quote, because the useful limit of the module is on time at the top of the frequency range and the table encodes it.

At 36 V in and 5 V out the duty cycle is 13.9 percent, so at 400 kHz the switch is on for 347 ns of a 2.5 us period, which is comfortable. At 2.4 MHz the same rail is on for 57.9 ns, and that is where a board that was qualified at 400 kHz starts to show jitter and a higher input current.

Thermal arithmetic for the 5 V rail

At 36 V to 5 V and 3 A the output is 15 W and an 88 percent figure puts 2.05 W inside the package, which on 24.4 C/W is a 50 C rise and about 75 C of ambient at a 125 C junction. The input current is only 0.47 A, so the connector and the input capacitor are easy, and the loss is dominated by the switching and the internal inductor rather than by conduction.

The same 3 A at 1.8 V out is 5.4 W and about 0.9 W of loss, a 22 C rise, so the low voltage rails in this family are thermally uninteresting and the 5 V and 12 V rails are where the 24.4 C/W has to be taken seriously.

Bias, burst mode and the 56 V sum

The bias pin needs at least 2.8 V and must not exceed 25 V, and the sum of VIN and BIAS has to stay below 56 V. Tying BIAS to a 5 V output is the normal arrangement and is inside both limits; tying BIAS to the 36 V input on a board that also runs the input at 36 V is inside the sum limit by 20 V but wastes the bias current in the internal regulator.

In burst mode the input current falls to about 50 uA, which is what a standby rail on a battery needs. The transition into burst mode is visible on the output as a small ripple increase, and a load that cannot tolerate that should hold the SYNC pin at a voltage that keeps the module in forced continuous operation.

What the I grade does and does not change

The E and I codes in this family are both -40 C to 125 C, and only the MP codes reach -55 C. The suffix changes the marking, the price and often the lead time rather than the window.

Two or more modules can be paralleled by tying VIN, ADJ, VOUT and the SHARE pins, which is how a 6 A rail is built from two 3 A parts. The share pins carry the current sharing signal and must be tied even when the outputs are already common, or the modules fight each other at the load step.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use the ADI second source page to confirm a substitute before it is fitted; OEM procurement is the routine for a part that has already stopped shipping.

Two questions buyers ask

Why does the document give resistor values instead of a frequency formula? Because the useful limit is on time rather than a formula. The RT table covers 200 kHz to 1.8 MHz in standard values, and a board qualified at one row is not automatically qualified at another.

Can two LTM8025 modules make a 6 A rail? Yes, with VIN, ADJ, VOUT and the SHARE pins tied. The share pins carry the sharing signal, so leaving them open defeats the arrangement even when the outputs are common.