LTM8024EY#PBF
Product Specifications
LTM8024EY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8024EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8024EY#PBF: 40 V in, 5 V out and the frequency that fits both channels
The LTM8024EY#PBF is the E grade of the 40 V dual module in the 9 mm by 11.25 mm by 3.32 mm ball grid array with SAC305 balls and MSL 3, 3.5 A per channel or 7 A with the channels tied. Both the E and the I codes are -40 C to 125 C, so the suffix does not change the temperature window in this family. The output range is 0.8 V to 8 V per channel and the switching frequency spans 200 kHz to 3 MHz.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 3 V to 40 V |
| Output voltage | 0.8 V to 8 V per channel |
| Output current | 3.5 A per channel, 7 A in parallel |
| Duty cycle at 5 V from 40 V | 12.5 percent |
| RT for 0.9 MHz | 41.2 k |
| RT for 2 MHz | 13 k |
| Junction to ambient | 18.0 C/W, 10.0 C/W to case top |
| Bias pin | at least 3.2 V for proper operation |
| Package | 9 mm x 11.25 mm x 3.32 mm BGA, MSL 3 |
| Temperature range | -40 C to 125 C, E grade |
A 40 V bus and a 5 V rail
At 40 V in and 5 V out the duty cycle is 12.5 percent, so at 2 MHz the switch is on for 62.5 ns. The module will run at that frequency, and the loss at 17.5 W out is about 2.39 W per channel at 88 percent, which is a 43 C rise on 18.0 C/W.
A pair of 5 V channels at 3.5 A each is 35 W out and 4.8 W of loss in a 9 mm by 11.25 mm body, which is a 86 C rise if both channels run flat out with no copper help. That is the point where the 4.5 C/W board path has to be built into the copper rather than assumed.
Running the two channels as one 7 A rail
Tying VIN, VOUT, FB and SHARE makes the two channels a single 7 A output, and tying the TRSS pins as well makes them start together. The channels run about 90 degrees apart through the CLKOUT arrangement, so the input ripple currents partly cancel and the input capacitor does not have to double.
The 7 A figure is the sum of the two 3.5 A channels at the same 80 C ambient condition. It is not a third rating and it does not come with extra thermal margin: the same 4.8 W of loss is still in the same 9 mm by 11.25 mm package.
BIAS, and why 3.2 V is the number
The internal housekeeping regulator runs from BIAS and needs at least 3.2 V. If the output is 3.2 V or higher, BIAS can be tied to the output, which is the efficient choice because the bias current then comes from the rail being regulated rather than from the 40 V bus.
Below 3.2 V output, BIAS has to come from VIN or another source, and the pin must stay below 10 V. A 0.8 V core rail with BIAS tied to a 40 V bus will work and will dissipate the difference in the internal regulator, which is a real loss on a rail that is otherwise only delivering 5.6 W.
Two channels, one frequency, and the EMC trade
The frequency is set by one resistor for both channels, so a dual 5 V and 3.3 V arrangement runs the same frequency on each. That is convenient and it means the 3.3 V channel at 8.3 percent duty and the 5 V channel at 12.5 percent share the same period, with the 3.3 V on time the shorter of the two.
At the top of the frequency range, 3 MHz with a 13 k resistor, the on time for a 3.3 V output from 40 V is 27.5 ns. The module supports it, and the board has to support it too: the input capacitor's ESR and the loop area start to dominate the ripple at that point.
When an order code in this family cannot be found, the power management cross reference lists what else does the same job, how to reduce component cost covers what to check before a part is dropped into an existing board, and BOM shortage recovery is the route we take on a live shortage.
Two questions buyers ask
Can BIAS be tied to a 0.8 V output? No. The pin needs at least 3.2 V. On a low output the BIAS pin has to come from VIN or another rail, and its voltage must stay under 10 V.
Do the two channels have to run at the same frequency? Yes. One resistor sets the oscillator for both. The channels can have different output voltages and different on times, but not different frequencies.