Contact Us

LTM8023IY#PBF

Brand: Analog Devices
Analog Devices LTM8023IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8023IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8023IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8023IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8023IY#PBF: The Industrial Grade 2 A Module in the Ball Grid Array Body

The LTM8023IY#PBF is the industrial temperature grade of the 2 A, 36 V step-down module in the ball grid array package, so it is specified over the full minus 40 to plus 85 degrees ambient range rather than the 0 to plus 85 window of the E grade. The electrical behaviour is the same as every other code in the family: 3.6 V to 36 V input, 0.8 V to 10 V output set by one resistor from a 0.79 V feedback threshold, 200 kHz to 2.4 MHz switching frequency set by a second resistor, and 2 A of output current with only bulk input and output capacitors around the package. The choice between this code and the LGA version is a production choice, and the choice between this code and the E grade is a temperature one.

Ball grid array against land grid array on the same die

The module is offered in a 9 mm by 11.25 mm land grid array 2.82 mm tall and in a ball grid array 3.42 mm tall, with the same footprint and the same electrical part inside. The LGA presents flat pads that are visible from the side after reflow, which makes automated optical inspection of the joint possible. The BGA presents balls under the body, so the joints can only be checked by X-ray or by electrical test, and the 0.6 mm of extra height is the cost of that difference. A production line that relies on optical inspection should choose the LGA, and a line that already X-rays its area arrays, or a board that needs the slightly taller body for clearance, can use the BGA without any electrical penalty.

Thermal path and the 2 A rating

Almost all of the heat leaves the module through the pads or balls into the board, so the copper under the part is part of the power rating. At 12 V in and 3.3 V out at 2 A the delivered power is 6.6 W, and at a realistic 85 percent efficiency the loss is about 1.16 W, which a 9 mm by 11.25 mm body can pass into a board with a reasonable copper area and cannot pass into a board with thin traces and no plane. The 2 A figure therefore holds at 12 V in and fails at 36 V in on the same board, because the loss rises with the input voltage even though the output current is unchanged.

ParameterValue on this order codeWhat it decides
Temperature gradeI, minus 40 to plus 85 degrees, fully specifiedThe E grade is guaranteed only from 0 degrees
PackageBGA, 9 mm by 11.25 mm by 3.42 mmJoints inspected by X-ray, not by camera
Ball finishSAC305, RoHSThe IY code without PBF is tin lead
Input range3.6 V to 36 VStart-up needs 5.5 V with RUN/SS at the input
Output0.8 V to 10 V at 2 ARADJ equals 394.21 over VOUT minus 0.79
Switching frequency200 kHz to 2.4 MHzHigher frequency means a smaller inductor is internal
Moisture sensitivityMSL 3168 hours of floor life once opened
Feedback threshold0.79 VThe real floor of the output range
Power goodValid within 10 percent of regulationSequencing has to allow for that window

The frequency resistor is a loss and size decision

A single resistor on the RT pin sets the switching frequency anywhere from 200 kHz to 2.4 MHz, and the trade is the one every switching regulator makes: a low frequency keeps the switching loss down but pushes the ripple current up and needs more output capacitance, and a high frequency shrinks the ripple and the capacitor but raises the switching loss and the minimum on-time constraint. The module's internal inductor is fixed, so the recommended frequency for a given input and output pair is given in the data sheet table rather than being a free choice, and using a much lower frequency than recommended is how a module ends up with an audible or a subharmonic behaviour that no amount of output capacitance fixes.

Where this code fits

Industrial control, instrumentation and networking equipment that has to work from minus 40 degrees without the cost of the MP grade are the natural sockets for the I code. Where the board has to be inspected optically, the LGA version of the same grade is the right order code, and where the ambient reaches plus 125 degrees the MP grade is the only one that is specified there. The pin to pin cross reference covers the body question, the ADI part second source page lists what a substitute has to match, and the one stop BOM sourcing page covers the module and its passive parts together.