LTM4646IY#PBF
Product Specifications
LTM4646IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4646IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTM4646IY#PBF: Twenty Amps From One Module, With a Remote Sense Pin on Each Channel
The LTM4646IY#PBF is a dual 10 A power module that can also be configured as a single 20 A output. Input range is 4.5 V to 20 V, or 2.375 V when the internal bias is supplied externally, and each channel covers 0.6 V to 5.5 V set by external resistors. Total dc output error is plus or minus 1.5 percent, efficiency reaches 96 percent, the switching frequency is adjustable from 250 kHz to 1.3 MHz with synchronisation, multiphase current sharing is supported, and each channel has a differential remote sense amplifier and an on-board temperature diode. Protection covers overcurrent foldback and output overvoltage, and the body is an 11.25 mm by 15 mm by 5.01 mm BGA.
Twenty amps in 168.75 square millimetres is 0.119 A per square millimetre. The reason that density is usable is the remote sense amplifier: at 20 A, 1 milliohm of board resistance between the module and the load is 20 mV, which is 2 percent of a 1.0 V rail and more than the accuracy of the module itself.
One milliohm of copper is bigger than the error budget
The module holds plus or minus 1.5 percent, which is 15 mV on a 1.0 V rail. A 20 A load through a milliohm of copper, which is a short wide trace and two vias, drops 20 mV. Without remote sense the load would see 1.5 percent from the module plus 20 mV from the copper, and the copper term would be the larger of the two. The differential sense pair moves the regulation point to the load, so the module compensates the drop instead of adding to it.
The sense lines carry almost no current, so they are a pair of thin traces from the module to the load. They have to be routed away from the switching node, and they have to connect at the point where the load actually is rather than at the bulk capacitor.
Ten amps per channel at 1.0 V is 10 W, and 20 A into 0.9 V is 18 W
Each channel delivers 10 W at a 1.0 V set point, so the pair delivers 20 W. As a single output the module delivers 20 A, which at 0.9 V is 18 W. From a 12 V input at 90 percent efficiency, 20 W of output is 1.85 A of input current, and at the full 20 A into 0.9 V it is 1.67 A. Those currents are modest, which is why a module of this class can be fed from a backplane through a single connector pin pair.
The 2.375 V minimum input with the bias supplied externally is the feature that lets a 2.5 V intermediate bus feed the module. Without that bias connection the minimum is 4.5 V, so a 2.5 V architecture needs the external bias or a different module. The internal bias can be fed from a 3.3 V housekeeping rail that already exists on the board.
Multiphase and frequency synchronisation are what keep the input quiet
Multiphase operation with current sharing runs the two channels out of phase, which halves the ripple current that the input capacitance has to absorb for the same total output current. At 250 kHz to 1.3 MHz there is also a choice of switching frequency, and the higher end shrinks the ripple at the cost of switching loss. Synchronising to a system clock keeps the module out of the band where a radio or a converter is listening.
The temperature diode on each channel is a real measurement rather than a thermal model. A system that derates on a measured die temperature rather than on an assumed one can run the module closer to its rating, and a system that never reads the diode is running on margin it has not verified.
| Function | Dual 10 A or single 20 A step-down power module |
| Input range | 4.5 V to 20 V, 2.375 V minimum with an external bias |
| Output range | 0.6 V to 5.5 V per channel, set by external resistors |
| Accuracy | Plus or minus 1.5 percent total, 15 mV on a 1.0 V rail |
| Sense | Differential remote sense per channel, 20 A through 1 milliohm is 20 mV |
| Output power | 10 W per channel at 1.0 V, 18 W as a single 20 A output at 0.9 V |
| Efficiency | Up to 96 percent at the stated operating point |
| Frequency | 250 kHz to 1.3 MHz, adjustable and synchronisable |
| Monitoring | Temperature diode per channel |
| Body | 11.25 mm by 15 mm by 5.01 mm BGA, 168.75 square millimetres |
Two questions buyers ask
Can the two channels be paralleled for 20 A?
Yes, that is the single output configuration, and the current shares between the channels through the module's own loop. The 20 A figure is the sum of two 10 A channels, so the thermal path still has to handle 20 A of dissipation in one body.
Does remote sense work with the channels paralleled?
The sense amplifier is per channel, and in the paralleled configuration the pair regulates a single node. A board that uses remote sense has to connect both sense pairs to the load point, and a board that senses at the module gets the module specification without the copper.
Ordering and supply
The IY suffix is the BGA body on the industrial grade. The family table lists three order codes, and the part is recommended for new projects at the vendor. The SnPb finish is available for lines still on tin lead, which matters for a module this size in a defence or industrial build.
We hold this module for networking and medical builds. Start at the analog mixed signal ICs page, the power management cross reference page is where the 20 A modules are compared, and medical device components covers the traceability a medical build needs on a power module.
Request Quote — In Stock, 100% New & Original, Full Warranty