LTM4637IY#PBF
Product Specifications
LTM4637IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4637IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4637IY#PBF: 20 A From a 4.5 V to 20 V Rail, and the Duty Cycle Limits Nobody Reads
The LTM4637IY#PBF is a complete 20 A step-down module in a 15 mm by 15 mm by 4.32 mm ball grid array, with the controller, the power field effect transistors, the inductor and the compensation all inside the package. The input range is 4.5 V to 20 V, the output range is 0.6 V to 5.5 V set by one external resistor, the total direct current output error is plus or minus 1.5 percent over minus 40 to plus 125 degrees, and four modules can be paralleled for 80 A. The part is pin compatible with the LTM4627, which is the 15 A member of the same family, so a current upgrade on an existing board is a component change rather than a board change.
Duty cycle, minimum on-time and the ratios that do not work
Two limits decide which input and output pairs are usable. The maximum duty cycle is 94 percent typical at 500 kHz, so a 5 V output from a 5.5 V input is at the edge of the range and a 5 V output from a 5 V input is outside it. The minimum on-time is 100 ns, so at 1 MHz a 20 V to 0.6 V conversion would need a 30 ns pulse and cannot be done, which means the 20 V input and the 0.6 V output are not simultaneously available at high frequency. Both limits are ordinary for a current mode buck, and both are invisible on the front page of the data sheet, which is why the ratio has to be checked against the frequency before a specification is committed.
Remote sense, tracking and the internal bias rail
The module has a differential remote sense amplifier for outputs at or below 3.3 V, which removes the voltage drop in the copper between the module and the load from the regulation loop. That is worth several tens of millivolts at 20 A on a real board, and it is the difference between a rail that meets its tolerance at the load and one that only meets it at the module pins. The track and soft-start pin allows the output to follow another rail during power-up, which is how sequencing is done without a separate sequencer, and the internal bias regulator that powers the drivers draws about 20 mA at 750 kHz, so its loss is the input voltage minus 5 V times that current: 0.3 W at a 20 V input, which is part of the thermal budget and not a rounding error.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Output current | 20 A, up to 80 A with four in parallel | Current sharing is a copper and tolerance question |
| Input range | 4.5 V to 20 V | 12 V rails directly, 5 V rails with care |
| Output range | 0.6 V to 5.5 V, one resistor | Set by the feedback divider at the load |
| Accuracy | Plus or minus 1.5 percent over temperature | Includes line, load and the internal reference |
| Maximum duty cycle | 94 percent typical at 500 kHz | A 5 V output needs more than 5.3 V of input |
| Minimum on-time | 100 ns | High input to low output needs a lower frequency |
| Remote sense | Differential, for outputs at or below 3.3 V | Removes copper drop at 20 A |
| Temperature monitor | Diode connected transistor output | Host can read die temperature |
| Package | BGA, 15 mm by 15 mm by 4.32 mm | Pin compatible with the 15 A LTM4627 |
Thermal reality at 20 A
At 1.0 V out and 20 A the module delivers 20 W, and the 88 percent efficiency that the data sheet quotes for a 12 V to 1.8 V conversion puts the loss in the region of 2.7 W, all of which leaves through the 15 mm square body into the board and, in most builds, into a heatsink. The current derating curves in the data sheet are drawn for a specific board and airflow, so a build that copies the reference circuit but not the copper will not reach 20 A. The temperature monitor diode exists because a 4.32 mm tall package at 20 A is a component whose junction temperature has to be observed rather than assumed, and the host reading it is the cheapest protection available.
Where the part belongs
Telecom and datacom line cards, field programmable gate array and processor core rails, storage controllers and test equipment that need a 20 A point of load converter from a 12 V backplane are the intended sockets. Where the current is lower, the 15 A LTM4627 shares the pinout, and where several rails have to track, the same family provides multi-output members. The ADI part second source page sets out what a substitute module has to match, the pin to pin cross reference covers the family pinout, and the one stop BOM sourcing page covers the module, its capacitors and the heatsink hardware on one order.