LTM4633MPY#PBF
Product Specifications
LTM4633MPY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4633MPY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4633MPY#PBF: Three Independent 10 A Rails in One 15 mm Package
The LTM4633MPY#PBF packs three independent 10 A step-down converters into one 15 mm by 15 mm by 5.01 mm ball grid array, which is the density argument in a single sentence: thirty amps of point of load conversion inside one outline, with the controllers, the field effect transistors, the inductors and the compensation all in the package. The input range is 4.7 V to 16 V, or 2.375 V to 16 V with an external 5 V bias, the first two outputs span 0.8 V to 1.8 V and the third spans 0.8 V to 5.5 V, each set by one resistor, and the total direct current output error is plus or minus 1.5 percent. The MP suffix is the widest temperature grade in the ordering table.
Two narrow outputs and one wide output is a deliberate split
Channels one and two stop at 1.8 V and channel three goes to 5.5 V, which looks arbitrary until the application is considered. The narrow channels are the ones that feed processor cores and field programmable gate array fabric, where the rail is below 1.8 V and the current is high, and they are the two channels that support multiphase operation with current sharing between them. The wide channel feeds the input and output interfaces, memory and analogue rails that sit at 1.8 V, 2.5 V, 3.3 V or 5 V. A system that needs three rails at 1.2 V is served by paralleling channels one and two and using channel three separately, and a system that needs three different high voltages at 10 A is not served by this part at all.
Power good, tracking and the sequencing that comes free
Each output has its own power good signal, and each has soft start and tracking, so a three rail sequence that has to come up in order can be built without an external sequencer. Tracking means one rail follows another during the ramp, which is what a processor datasheet usually asks for, and it is a wiring choice on the track pin rather than a software feature. The cost of using it is that a fault on the master rail takes the follower down with it, which is usually the desired behaviour and occasionally is not.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Outputs | 3 channels, 10 A each | 30 A total in one 15 mm package |
| Input range | 4.7 V to 16 V, 2.375 V with a 5 V bias | A 3.3 V input needs the external bias |
| Output one and two | 0.8 V to 1.8 V | Core and fabric rails, multiphase capable |
| Output three | 0.8 V to 5.5 V | Interface and analogue rails |
| Accuracy | Plus or minus 1.5 percent maximum | Total direct current error over temperature |
| Power good | One signal per output | Sequencing without an external supervisor |
| Tracking | Soft start and voltage tracking per channel | Rails ramp together or in order |
| Protection | Overvoltage and overcurrent per channel | A fault stays local to one rail |
| Package | BGA, 15 mm by 15 mm by 5.01 mm | Tallest body in the family, needs airflow or copper |
Thirty amps in one outline is a board temperature decision
At 1.0 V and 10 A per channel the module delivers 30 W in total, and at a realistic efficiency the loss is several watts inside a 15 mm square body. That heat has to leave through the balls into the board and, above a few watts, into a heatsink or an airflow path as well. The three channels are close together by construction, so the thermal coupling between them is strong: running two channels at full load heats the third one's die even when its own load is light. That is why the derating curves are drawn per channel with the others loaded, and why a board that cools the module for one channel's loss will not hold three.
Where the part fits
Telecom and networking line cards, industrial controllers with a processor and two interface rails, and instruments that need three supplies from one 12 V input are the intended sockets. Where the rails are all below 1.8 V and the current is higher, a dual output module with parallel capability is the better fit, and where the rails include a negative voltage this family does not apply. The ADI part second source page sets out what a substitute has to match, the pin to pin cross reference covers the package and pinout, and the one stop BOM sourcing page covers the module and its output capacitors on one order.
The external bias pin is what makes a 3.3 V input possible
The input range is 4.7 V to 16 V on the input pins alone, and 2.375 V to 16 V when an external 5 V bias is supplied, because the internal drivers need a voltage above the input to turn the field effect transistors fully on. A 3.3 V backplane therefore has to provide that 5 V rail from somewhere else on the board, and the sequencing matters: the bias has to be present before the module is enabled, or the module will try to start with insufficient gate drive and either fail to regulate or run hot. That single requirement is the reason many three rail boards derived from 3.3 V end up using a boost converter ahead of the module rather than a linear regulator.