LTM4633EY#PBF
Product Specifications
LTM4633EY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4633EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4633EY#PBF: the E grade of the triple 10 A module, and the 7.5 degree C per watt that sets the rails
The LTM4633EY#PBF is the E grade of the triple 10 A module in the 15 mm by 15 mm by 5.01 mm package, with 4.7 V to 16 V input, two 0.8 V to 1.8 V channels and one 0.8 V to 5.5 V channel at 10 A each, plus or minus 1.5 percent of dc error and temperature monitors brought out to pins. Both grades are listed at minus 40 degree C to 125 degree C on this part, so the suffix is a guarantee choice. What decides a build is the 7.5 degree C per W and the way the loss is distributed across three rails of different voltage.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 4.7 V to 16 V |
| Bias assisted input | 2.375 V to 16 V with an external 5 V bias |
| Output 1 and 2 | 0.8 V to 1.8 V at 10 A |
| Output 3 | 0.8 V to 5.5 V at 10 A |
| DC output error | plus or minus 1.5 percent |
| Thermal resistance | 7.5 degree C per W |
| E grade range | minus 40 degree C to 125 degree C |
| Monitors | temperature monitors and power good per output |
| Synchronization | external frequency synchronization |
| Package | BGA, 15 mm x 15 mm x 5.01 mm |
| Sequencing | soft start and tracking |
| Protection | overvoltage and overcurrent |
The loss is not shared equally, so the thermal budget is not either
A 1.0 V, 1.2 V and 3.3 V set of rails at 10 A each is 10 W, 12 W and 33 W of output. The 3.3 V channel carries more than half the power and therefore most of the loss, so the junction temperature is set by that channel while the other two are cool. The 7.5 degree C per W is a package figure, so the die is at one temperature and the hot channel is what moves it.
The practical consequence is that the 5.5 V capable channel should be loaded last. A build that needs 3.3 V at 8 A and 1.0 V at 10 A is better served by putting the 3.3 V rail on the channel that has the most copper and treating the other two as support rails. On a 58 W total the 7.9 W of loss gives a 59 degree C rise, which is the figure to compare against the ambient rather than a per channel number.
Where the 16 V input limit bites
Sixteen volts in and 0.8 V out is a 5 percent duty cycle, and at the switching frequency that is a short pulse. The 16 V maximum is comfortable for a 12 V rail at plus ten percent (13.2 V) and for a 12 V rail with a modest transient. A 15 V rail at plus ten percent is 16.5 V and outside the part, so a 15 V backplane needs a clamp or a different module.
The low end of the input range is more interesting on this part because of the bias assisted mode: with a 5 V bias the module runs from 2.375 V, which lets a 3.3 V rail or a 2.5 V rail feed three outputs. Without the bias the minimum is 4.7 V, so the bias pin is what makes the part usable on a low voltage system rather than the input rating itself.
Three rails, one package, and one set of sequencing pins
Each output has its own soft start and tracking pin, so the three rails can be ramped in a defined order without external sequencers. That is the reason a triple module exists: three separate regulators would need three enable circuits and three power good signals, and the sequencing would be built from discrete parts.
The tracking function also allows one rail to follow another, which is what a memory rail or an analog supply often needs. On a package with three rails and one thermal limit, the sequencing order is also a thermal decision: bringing the 3.3 V channel up last means the package is already warm from the other two when its own loss arrives, and the inrush of the largest rail is the peak dissipation of the whole sequence.
The pages that answer this most often are the power management cross reference for the family alternatives, vendor consolidation for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the E grade different from the I grade on this module? The ordering table lists both at minus 40 degree C to 125 degree C with the same body and ballout, so the difference is the guarantee, the part marking and the finish code. A substitution between them does not change the thermal case or the footprint.
Can the module run from a 3.3 V rail without a 5 V bias? No. The 2.375 V minimum applies only when the external 5 V bias is present, and the unassisted minimum is 4.7 V. A 3.3 V system has to provide the bias rail, which is a small load but a separate connection, and a board that omits it does not start.
The bias rail draws current even when the outputs are off
In the bias assisted configuration the external 5 V rail supplies the internal drivers, so it draws current whenever the module is enabled, including the period when the outputs are still ramping. A system that treats the bias rail as a logic supply and sizes it for a few milliamps finds it loaded by the switching stage instead, and the bias rail sags during start-up, which lengthens the ramp and can trip the input undervoltage lockout on the module.
The safe approach is to derive the bias from a rail that is already up and can supply the driver current, and to check the bias voltage at the pin during a full load start rather than at steady state. A 5 V bias that measures 5.0 V idle and 4.6 V during start is the classic symptom, and the module's own behaviour then looks like a soft start fault rather than a bias supply problem.