Contact Us

LTM4632EY#PBF

Brand: Analog Devices
Analog Devices LTM4632EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4632EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4632EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4632EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4632EY#PBF: a 3.3 V input memory rail and the resistor values that set it

The LTM4632EY#PBF is the E grade of the DDR-QDR4 module in the 6.25 mm by 6.25 mm by 2.42 mm ball grid array with SAC305 balls and MSL 3. It runs from 3.6 V to 15 V in, and the vendor notes that a 3.3 V input works with VIN tied to INTVCC, which is the arrangement most DDR4 boards want. The E grade is -40 C to 125 C, the same window as the I grade in this family, and the output is set by a single resistor per rail.

Published values

ParameterValue
Input voltage3.6 V to 15 V, 3.3 V with VIN tied to INTVCC
Output setting for 1.0 V90.9 k
Output setting for 1.2 V60.4 k
Output setting for 1.5 V40.2 k
Output setting for 1.8 V30.1 k
Output setting for 2.5 V19.1 k
Output current3 A per rail, VTT sinks and sources
Output capacitance22 uF ceramic per output in the reference circuit
Junction to ambient20 C/W
Temperature range-40 C to 125 C, E grade

A 3.3 V bus and the INTVCC tie

The module's minimum input is 3.6 V and a 3.3 V rail at minus 5 percent is 3.135 V, which is below it. The vendor's answer is to tie VIN to INTVCC, which changes the internal bias arrangement and lets the part run from a 3.3 V bus.

That tie is not optional on a 3.3 V board and it is not something to be discovered at board review. A board that leaves VIN on the 3.3 V rail without the INTVCC tie has a module that will not start at the bottom of the rail's tolerance, and the failure appears only on the units that sit at minus 5 percent.

The resistor table is the whole configuration

One resistor per rail sets the output: 90.9 k for 1.0 V, 60.4 k for 1.2 V, 40.2 k for 1.5 V, 30.1 k for 1.8 V and 19.1 k for 2.5 V, with an open pin for 0.6 V. The reference is 0.6 V, so the divider ratio is fixed by the standard values and a 1 percent part is what keeps the rail inside the 1.5 percent total error.

A DDR4 VDDQ rail at 1.2 V has a JEDEC window of plus or minus 3 percent, and the module's own total error of 1.5 percent leaves half of that for the resistor and the board. That is enough, and it is not enough to absorb a 5 percent resistor, which is the mistake that shows up as a rail that measures good on the bench and fails the memory test at temperature.

22 uF per output and what it buys

The vendor's reference circuit uses one 22 uF low ESR ceramic per output and claims low ripple and good transient response from that alone. The high switching frequency is what makes a single capacitor enough, and the frequency is set by the same resistor that sets the output, so the two decisions are coupled.

Lowering the frequency to improve efficiency raises the ripple and the transient droop, and a board that changes the RT value without rechecking the output capacitor is trading a memory margin it cannot see for an efficiency number it can.

What the E grade means on a memory rail

The E code is -40 C to 125 C, identical to the I code. There is no MP grade in this family, so a -55 C requirement cannot be met by any order code and needs a different part.

A memory rail is usually specified at the top of the range rather than the bottom, because the memory itself runs hot. The 20 C/W junction to ambient with 0.64 W of loss at 1.2 V and 3 A is a 13 C rise, so the module is not the hot part in that corner of the board.

Two pages worth reading before a purchase order goes out are the power management cross reference and the pin to pin cross reference; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to reduce component cost covers the case where the shortage is already on the line.

Two questions buyers ask

Will the module run from a 3.3 V rail without any special connection? Only with VIN tied to INTVCC, which the vendor specifies for 3.3 V operation. The 3.6 V input minimum is above a 3.3 V rail at minus 5 percent.

Is there a -55 C code in this family? No. The order table carries only E and I codes, both -40 C to 125 C. A -55 C requirement needs a different device.