Contact Us

LTM4632EV#PBF

Brand: Analog Devices
Analog Devices LTM4632EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4632EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4632EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4632EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4632EV#PBF: VTT tracking, soft start and a two phase 6 A termination rail

The LTM4632EV#PBF is the E grade, Au pad, land grid array body of the DDR-QDR4 module at 6.25 mm by 6.25 mm by 1.82 mm with MSL 3. Its second channel can be configured as a 3 A VTT termination rail tracking VDDQ / 2, or the two channels can be paralleled into a single 6 A VTT rail for a wide memory bus. Input range is 3.6 V to 15 V and the total output error is 1.5 percent over line, load and temperature.

Published values

ParameterValue
Input voltage3.6 V to 15 V
VDDQ rail3 A, 0.6 V to 2.5 V
VTT rail3 A sink and source, tracks VDDQ / 2
Two phase VTT6 A with the channels paralleled
TrackingTRACK/SS1 pin with a 1.2 uA pull up
Burst modechannel 1 only
Minimum on and off time20 ns and 45 ns
Junction to ambient20 C/W, 17 C/W to case top
Package6.25 mm x 6.25 mm x 1.82 mm LGA, MSL 3
Temperature range-40 C to 125 C, E grade

Tracking is the point of the second channel

VTT has to come up with VDDQ and sit at half of it, or the memory sees a rail that is out of sequence during power up. The TRACK/SS1 pin has a 1.2 uA pull up and follows an external ramp, so the VDDQ rail's rise is what sets the timing and the termination rail arrives with it rather than after it.

A board that lets VTT come up on its own internal soft start can still pass a functional test and fail a repeated power cycle test, because the memory is being biased in an order it does not expect. The tracking pin is cheap to use and it is the difference between a rail that is sequenced and one that is merely present.

Two phases for a 6 A termination rail

Paralleling the two channels into one 6 A VTT rail is the arrangement for a wide bus, where the termination current is the sum of many resistors rather than one. The channels share current and run out of phase, which halves the input ripple and lets the input capacitor stay small.

The 6 A is a sum of two 3 A rails in one 6.25 mm square body, so the thermal story does not change: 6 A at 0.6 V is 3.6 W out and the loss at 80 percent is 0.9 W, which on 20 C/W is an 18 C rise. It is a comfortable part of the package's range and the limit is the current, not the heat.

Burst mode on channel 1 only

The vendor enables burst mode on channel 1 only, which is the VDDQ side. VTT stays in continuous conduction, because a termination rail that goes into burst moves with the data pattern.

SYNC and mode selection are on the same pin: tying it to ground forces continuous synchronous operation at all loads, and floating or biasing it enables burst on channel 1. A board that wants both rails quiet should ground that pin and accept the light load efficiency, which at these currents is a few tens of milliwatts.

Switching frequency and the two channels

The frequency is set by one resistor for both channels and can be synchronised to an external clock. With both channels on the same clock and 180 degrees apart, the input current ripple is the sum of two interleaved waveforms and the input capacitor sees roughly half the ripple of a single channel at the same total current.

The 20 ns minimum on time applies to each channel. At 15 V in and a 0.6 V VDDQ the duty cycle is 4 percent and the frequency ceiling is 2 MHz, and at 3.6 V in the same output is a 17 percent duty cycle with no such limit.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use one stop BOM sourcing to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.

Two questions buyers ask

Why does VTT need to track VDDQ? Because the termination resistors sit between the data lines and VTT, so the termination voltage has to follow the memory supply or the bus sees an offset. The TRACK/SS1 pin is what makes the two rails rise together.

Can both channels be used for 6 A of VDDQ? The vendor's two phase configuration is for a single 6 A VTT rail. Using both channels for VDDQ would leave the termination rail without a source, so the arrangement is one or the other.