LTC6101HVCIS5#TRPBF
Product Specifications
LTC6101HVCIS5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC6101HVCIS5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC6101HVCIS5#TRPBF: the 100 V high side current sense amplifier in SOT-23
What this order code is
LTC6101HVCIS5#TRPBF is the high voltage member of the LTC6101 current sense family in the 5-lead SOT-23, tape and reel. The HV part operates from 5 V to 100 V of supply with a 105 V absolute maximum, against 4 V to 60 V and 70 V absolute maximum on the standard part, so the two differ in the bus they can sit on rather than in the way they measure.
The part converts the voltage across an external shunt into an output current, which is then turned back into a ground referenced voltage by a resistor. Gain is set by two resistors, which is what lets the same amplifier serve a 50 mV full scale measurement and a 5 mV one. Maximum input sense voltage is 500 mV, offset is 300 uV maximum, and the response time is 1 us for a 0 to 2.5 V step at the output.
Parameters as published
| Item | Value |
|---|---|
| Supply range, HV part | 5 V to 100 V, 105 V absolute maximum |
| Maximum sense voltage | 500 mV |
| Input offset voltage | 300 uV maximum |
| Input bias current | 170 nA maximum |
| Gain | set by two external resistors |
| Response time | 1 us, 0 to 2.5 V output step |
| Power supply rejection | 118 dB minimum |
| Output current | 1 mA maximum |
| Supply current | 250 uA at 12 V |
| Specified range | -40 C to 125 C |
| Operating range | -55 C to 125 C |
| Body | 5-lead SOT-23, 1 mm profile |
| Packing | tape and reel |
Numbers that decide the application
The shunt choice is the whole measurement. A 10 milliohm shunt at 5 A develops 50 mV, which is a tenth of the 500 mV full scale, so the amplifier runs at a gain that leaves resolution on the table; a 1 milliohm shunt at 20 A develops 20 mV and dissipates 400 mW; a 0.5 milliohm shunt at 50 A develops 25 mV and dissipates 1.25 W. Every step down in shunt resistance buys loss and costs signal, and the 300 uV offset is the floor that decides when the trade stops paying.
Put numbers on that floor. Three hundred microvolts is 0.6 percent of a 50 mV signal, 1.5 percent of 20 mV, 1.2 percent of 25 mV and 3 percent of a 10 mV signal at 100 mA. So a 10 milliohm shunt at 5 A measures to about half a percent before gain resistor tolerance is counted, and a 100 milliohm shunt at 100 mA measures to about 3 percent. The same part covers both, and the accuracy is set by where on the scale the application sits.
Gain and output current are coupled. A gain of 20 on a 50 mV signal gives 1 V, and into a 1 kohm output resistor that is 1 mA, which is exactly the output current limit of the part. A gain of 50 with the same shunt and the same resistor would ask for 2.5 mA and would not be delivered, so the resistor and the gain have to be chosen together rather than one after the other.
Power supply rejection of 118 dB is 1.26 uV per volt of supply change, which at a 48 V common mode is 60 uV referred to the input, a fifth of the offset. That is why the part can sit directly on a telecom bus without a separate low voltage rail for the amplifier.
Where it fits and where it does not
It fits high side monitoring on a 48 V telecom bus, a 72 V or 96 V battery string, a motor supply, a hot swap current limit and any line where the shunt sits above the logic supply. It does not fit a bus above 105 V, a sense voltage above 500 mV, an application that needs an output above 1 mA into its resistor, or a measurement where 300 uV of offset is a large fraction of the signal and no calibration is possible.
Supply and second source questions
The HV and standard parts share a body and a pin map but not a supply ceiling, so a cross reference that matches on package will fail on a 100 V bus. The grade and temperature letters in the middle of the order code are defined in the ordering table, and the family figures above are maxima that apply across those letters. Current sense and monitoring parts are grouped on the converter and monitoring cross reference page.
Sourcing notes and next step
We quote the HV code with the SOT-23 body and the tape and reel packing stated, and we will confirm which grade and temperature letters the stock carries rather than assume them. Send the line items and required date through the BOM shortage recovery page and we will answer with availability. The wider analog range is on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty