LTC6101HVACS5#TRPBF
Product Specifications
LTC6101HVACS5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC6101HVACS5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC6101HVACS5 high side current sense on a 48 V bus
The LTC6101HVACS5 is the A letter, C temperature letter, five lead SOT-23 member of a high side current sense family that runs from 5 V to 100 V of supply with a 105 V absolute maximum. The A and C letters are grading and temperature codes, not different functions: every member converts the drop across an external shunt into an output current, so the sense resistor and the two gain resistors set the answer, and the part itself is a transconductance stage with a 1 mA output limit.
What the 100 V ceiling buys and what it does not
A 48 V telecom bus at plus 10 percent is 52.8 V, which is 47 V below the operating ceiling and 52 V below the absolute maximum. A 72 V battery string at full charge is 82.1 V with eight 12 V blocks at 13.7 V each, still inside. What the ceiling does buy is margin against the transient that rides on those buses, and the margin is small: the operating ceiling is 100 V and the absolute maximum is 105 V, which is 4.76 percent, so a clamp or a transient suppressor belongs on the bus side rather than a hope that the amplifier survives it.
The errors that decide the shunt value
| Term | Published figure | Effect on a 10 mohm shunt at 5 A |
|---|---|---|
| Offset voltage | 300 uV maximum | 0.6 percent of the 50 mV sense drop |
| Input bias current | 170 nA maximum | 170 uV through 1 kohm, 1.7 mV through 10 kohm |
| Common mode rejection | 118 dB minimum | 126 uV referred to the input at 100 V of common mode |
| Shunt power | derived | 0.25 W in the shunt at 5 A |
Two of those rows move together. A smaller shunt reduces the 0.25 W that the resistor burns, but every millivolt removed from the sense drop raises the share that the 300 uV offset and the 126 uV of common mode error take. At 5 mV of sense drop the offset alone is 6 percent of the signal, so a 1 mohm shunt at 5 A belongs only where a 6 percent current reading is acceptable. The bias current is the row that a board gets wrong quietly: 170 nA into a 10 kohm gain resistor is 1.7 mV, five times the offset, so the two gain resistors want to stay in the low kiloohm range and the resulting output current then has to fit the 1 mA limit.
Supply current on a permanently live monitor
The published supply current is 250 uA at 12 V and 375 uA typical at 60 V. Over a year those are 2.19 Ah and 3.29 Ah, which is real capacity in a battery product and irrelevant in a rack. At 100 V the same 375 uA is 37.5 mW in a body that is 1 mm tall, so the part is not a thermal problem in any mount, and the reason to switch to a lower voltage member of the family is the sense range, not the dissipation.
Where this code fits
Telecom rectifiers, 48 V rack current monitoring, battery string current on a high voltage pack, and motor drives that sit on a 48 V or 60 V rail. The response time of 1 us for a 0 V to 2.5 V output step is fast enough for a hardware overcurrent comparator that has to act inside one switching period, and slow enough that the output filter has to be chosen for the noise of the switching stage rather than for the amplifier.
Sourcing notes and next step
Order the letter combination that the board was qualified with. The A letter and the C letter appear in the same five lead body, so a distributor line that lists only the family name does not tell you which grade arrives. If the original part is short, compare grades against the offset budget rather than against the price sheet, and check the temperature letter against the ambient inside the enclosure: the family page publishes -40 to 125 C as the specified range and -55 to 125 C as the operating range, and the guaranteed window for each letter is in the ordering information. Our second source page for ADI parts lists the equivalents we can quote, the BOM shortage route covers mixed bills, and the analog and mixed signal category holds the rest of the current sense family.
Request Quote — In Stock, 100% New & Original, Full Warranty