LT8614IUDC#TRPBF
Product Specifications
LT8614IUDC#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT8614IUDC#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT8614IUDC#TRPBF: a 1.2 V core rail that holds at light load
The LT8614IUDC#TRPBF is the I grade of the 4 A, 42 V Silent Switcher in the 18-lead 3 mm by 4 mm QFN, guaranteed over the full minus 40 C to 125 C junction range. In a digital product it is usually the rail that feeds a processor core: a low voltage, high current output from a 12 V or 24 V bus, where the converter has to hold regulation when the load steps between milliamps and amps and where the switching frequency has to be high enough to keep the inductor and the output capacitance small.
The figures behind a core rail
| Grade on this code | I, guaranteed minus 40 C to 125 C junction |
| Input range | 3.4 V to 42 V |
| Output current | 4 A |
| Minimum on time | 30 ns |
| Frequency | 200 kHz to 3 MHz, synchronisable |
| Light load mode | burst mode or pulse skipping at the SYNC pin |
| Quiescent current | 2.5 uA in burst mode |
| Output ripple in burst mode | under 10 mV peak to peak at any load |
| Dropout | 125 mV at 1 A |
Duty cycle, on time and a 1.2 V output
A 12 V to 1.2 V conversion has a 10 percent duty cycle, and at 2 MHz that is 50 ns of on time, comfortably above the 30 ns floor. At 3 MHz it is 33.3 ns, still above. The floor only starts to bind at 24 V to 1.2 V, which is a 5 percent duty cycle and 25 ns at 2 MHz, below the floor; the ceiling for that ratio is 1.67 MHz. A core rail from a 12 V bus therefore has the whole frequency range available and a core rail from a 24 V bus does not.
The inductor for 1.2 V at 2 MHz is small: 1 uH gives a ripple of 0.53 A, so the 4 A load peaks at 4.27 A and a 1.5 uH part gives 0.35 A and a 4.18 A peak. The 125 mV of dropout at 1 A is not a constraint at 1.2 V out, and the 3.4 V minimum input is the only limit that matters at the bottom. What does matter is the output capacitance: a core rail with a large ceramic bank and a fast load step needs the loop to be stable with the ESR that the bank presents, and the internal compensation of this part is fixed for a range of output capacitance rather than for any value.
Burst, pulse skipping and the processor sleep state
A processor core that drops to a few milliamps between bursts of work is the classic case for burst mode: the regulator stops switching, the output is held by the capacitor, and the 2.5 uA quiescent current is what makes the standby budget. The cost is a 10 mV ripple and a burst frequency that moves with the load, which can be audible or visible in a sensitive analog section. Pulse skipping keeps the clock running and drops pulses, which is the mode for a rail that shares a board with a radio or a converter that must stay synchronised.
The transition between the modes is the part that is hard to get right in a product. A rail that switches from burst to pulse skipping under software control will show a transient at the moment of the switch, and a processor that is running from that rail may see it as a brownout if the output capacitor is small. The usual answer is to switch modes only when the load is known to be low and to keep enough output capacitance to absorb the transition.
Two questions buyers ask
Does the I grade matter for a core rail? For an indoor product, no; the E grade covers a cabinet that stays above 0 C. For equipment that is stored unheated or shipped through a cold chain and powered up on arrival, the I grade is the guarantee that the rail comes up at minus 40 C rather than the promise that it should. The two are different order lines, so the choice is made at the bill of materials.
Can two of these make a 8 A rail? Not by paralleling the outputs directly, because the internal compensation and the peak current mode loop are not arranged for current sharing between two independent parts. Two phases can be run from a common clock with the SYNC pin, each feeding its own inductor into the same output node, and that is a supported arrangement for the family; the sharing is then set by the inductor resistances rather than by an active loop, so the two phases need matched inductors.
Sourcing notes and next step
Give the exact code with the I grade letters and the packaging suffix, the bus voltage and the load profile, and the quote is built on the grade and the reel the line needs. Our component cost page shows how a single 4 A part compares with two phases, the BOM shortage page covers the substitution rules, and the analog and mixed signal category lists the rest of the family.
Request Quote — In Stock, 100% New & Original, Full Warranty