Contact Us

LT8610AIMSE#TRPBF

Brand: Analog Devices
Analog Devices LT8610AIMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT8610AIMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT8610AIMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT8610AIMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT8610AIMSE#TRPBF: 3.5 A with a 30 ns minimum on time

LT8610AIMSE#TRPBF is the adjustable output version of the LT8610A in the 16-lead MSOP, on tape and reel, in the industrial grade. It is the part to look at when a 2.5 A rail is not enough or when a 42 V input has to feed 3.3 V at a switching frequency above 1.6 MHz, because the 30 ns minimum on time is the whole difference against the LT8610.

Published values

ParameterValue
Input voltage3.4 V to 42 V
Continuous output3.5 A
Feedback reference0.970 V, 0.964 V to 0.976 V
Minimum on time30 ns
Switching frequency200 kHz to 2.2 MHz
Top switch current limit5 A minimum, 6.7 A typical
Bottom switch on resistance65 mOhm
Bottom switch current limit3.4 A minimum
Efficiency95 percent at 1 A, 5 V out from 12 V
Quiescent current2.5 uA, 21.9 mAh over a year
Power goodplus or minus 9 percent, 297 mV at 3.3 V
Thermal resistance40 C/W junction to ambient
GradeI, guaranteed over -40 to 125 C
Difference from the LT86103.5 A against 2.5 A, 30 ns against 50 ns

Where the extra ampere goes

A 3.5 A rail at 5 V is 17.5 W. At 95 percent the loss is 0.92 W and the junction rises 37 C on 40 C/W, so a 125 C part holds a full load at 88 C ambient before any other heat source is counted.

The bottom switch limit of 3.4 A minimum sits 0.1 A below the continuous rating, which is unusual and worth noticing: in a sustained overload the bottom switch protects the part slightly before the headline current is reached. That is a deliberate choice in a part that has to survive an inductor that saturates, and it means the 3.5 A figure is a thermal and average rating rather than a peak promise.

30 ns and the frequency it unlocks

A 42 V to 3.3 V ratio is 7.86 percent duty. With a 30 ns floor the highest frequency that ratio supports is 2.62 MHz, so the full 2.2 MHz band is available and the inductor can be small. With the 50 ns floor of the LT8610 the same ratio is capped at 1.571 MHz.

That is a factor of 1.4 in frequency, which is a factor of 1.4 in inductor size for the same ripple and a similar factor in output capacitance for the same transient. On a dense board that is the reason to pay for the A rather than the base part.

The reference window, unchanged from the family

0.964 V to 0.976 V is a 12 mV window, 1.24 percent, against 18 mV on the LT8610. At a 3.3 V output that is 41 mV instead of 61 mV, which is a real improvement and a reminder that the A is not only a current upgrade.

The power good window stays at plus or minus 9 percent, 297 mV at 3.3 V. It is a flag, not a supervisor, and a load that cannot run below 3.0 V needs its own monitor with a sharper threshold.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, how to verify a drop in replacement is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Will the A drop into a board built for the LT8610? Pin for pin yes, in the adjustable version, because pin 16 is FB on both. The compensation is internal and the reference matches at 0.970 V, so the divider does not change. The current rating and the minimum on time are what improve.

Why is the bottom switch limit lower than the output rating? It is 3.4 A minimum against a 3.5 A rating. The bottom switch carries the inductor current during the off time, and the limit is set to protect the part when the inductor saturates rather than to define the continuous rating.