Contact Us

LT8610EMSE#WTRPBF

Brand: Analog Devices
Analog Devices LT8610EMSE#WTRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT8610EMSE#WTRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT8610EMSE#WTRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT8610EMSE#WTRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT8610EMSE#WTRPBF: automotive release at the 125 C junction limit

LT8610EMSE#WTRPBF is the E grade of the LT8610 in the 16-lead MSOP with the W automotive suffix. The E grade is tested from 0 C to 125 C junction and the colder part of the range is assured by characterisation, so this code suits a module whose cold spec starts at 0 C or above, and it is the cheapest way to put a Q100 screened 2.5 A buck on a board.

Published values

ParameterValue
GradeE, tested from 0 C to 125 C, cold end assured by characterisation
ReleaseW, automotive
Input voltage3.4 V to 42 V
Continuous output2.5 A
Feedback reference0.970 V, 0.964 V to 0.982 V
Minimum on time50 ns
Switching frequency200 kHz to 2.2 MHz
Dropout200 mV at 1 A
Efficiency96 percent at 1 A, 5 V out from 12 V
Quiescent current2.5 uA
Power goodplus or minus 9 percent
Thermal resistance40 C/W
Package16-lead MSOP, automotive marking

Where the 0 C guarantee is enough

A module inside the cabin, powered from a 12 V bus, is specified from -20 C to 85 C in most vehicle programmes, so a part tested from 0 C is not enough on its own. The E grade is the wrong buy for that cold start unless the assembly is characterised as a whole.

Where it fits is a body control module, a lighting driver or an accessory that is not required to operate below freezing, and where the qualification file accepts characterisation for the cold end. The H grade at 150 C is the usual automotive choice for the hot end, and the E grade is the one for a cost target with a narrow temperature clause.

The same 42 V transient, the same 50 ns floor

The input range tops out at 42 V, which is the load dump level the family is built for, and the minimum on time is 50 ns. Into 3.3 V that caps the frequency at 1.571 MHz; into 5 V it allows 2.2 MHz with 4 ns of margin.

For an automotive 3.3 V rail the practical answer is 1.5 MHz or below, which raises the inductor value and the output capacitance but keeps the loop out of pulse skipping at the low line end. A board that runs 2.2 MHz into 3.3 V from a 40 V transient will skip pulses during the event and the output will show it.

Power good and the divider, on an automotive rail

The power good window is plus or minus 9 percent, which is 297 mV at 3.3 V and 450 mV at 5 V. It is wide enough to ignore a cold crank sag and narrow enough to flag a rail that has not started, and it is not a substitute for an undervoltage supervisor on a load that cannot run below 3.1 V.

The reference window of 18 mV is 1.86 percent, which is 61 mV at a 3.3 V output. A two resistor divider of 1 percent parts adds roughly 1.4 percent more, so the divider is the term to tighten first when a 3 percent rail is missed.

Two pages worth reading before a purchase order goes out are the power management cross reference and vendor consolidation; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to reduce component cost covers the case where the shortage is already on the line.

Two questions buyers ask

Is the E grade a cold-weather part? No. It is guaranteed from 0 C to 125 C, and the -40 C end is assured by characterisation. A vehicle module that must start below freezing needs the I or H grade.

Does the W suffix add a temperature range? No. The W is the automotive release, and the temperature range comes from the grade letter: E is 0 to 125 C tested, I and H are guaranteed over the full -40 C end, and H goes to 150 C.