LTC4279IUFD#PBF
Product Specifications
LTC4279IUFD#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC4279IUFD#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC4279IUFD#PBF: one port of Power over Ethernet from 30 W up to 123 W
The LTC4279IUFD#PBF is an Analog Devices single port power sourcing equipment controller for IEEE 802.3at Type 1 and Type 2 systems and for LTPoE++ up to 90 W. It runs autonomously, with no microcontroller, and needs only a single supply and a small number of passive parts. Detection uses a four point mechanism to reject false powered device detection, classification is physical layer, and the current thresholds follow the assigned class. The output stage uses an external low on resistance MOSFET with a 0.1 ohm sense resistor, which is how the part keeps its dissipation low without a heat sink. It supports two pair and four pair output power, dual signature powered devices, an UltraPWR mode for custom loads up to 123 W, and a pin selectable detection backoff timer for midspan operation. The OUT pin is protected to plus or minus 80 V. It is on the analog and mixed-signal IC line card.
Where the 30 W and the 25.5 W come from
IEEE 802.3at Type 2 defines 30 W available at the power sourcing equipment and 25.5 W at the powered device, so 4.5 W is the budget for the cable and the connectors. At 54 V, 30 W is 0.556 A. LTPoE++ raises the port to 90 W, which is 1.67 A at the same voltage, and the 0.1 ohm sense resistor then dissipates 0.28 W on its own. UltraPWR at 123 W is 2.28 A and 0.52 W in the sense resistor. Those two numbers are why the sense element is a low value resistor and why the MOSFET has to be a low on resistance device rather than an integrated switch.
| Mode | Power at the port | Current at 54 V | Loss in 0.1 ohm sense |
|---|---|---|---|
| 802.3at Type 2 | 30 W, 25.5 W at the load | 0.556 A | 0.031 W |
| LTPoE++ | 90 W | 1.67 A | 0.278 W |
| UltraPWR | 123 W | 2.28 A | 0.519 W |
| Cable budget, Type 2 | 30 W minus 25.5 W | 4.5 W for cable and connectors | not in the PSE |
Autonomous operation is the point of the part
A PSE that needs firmware to detect, classify and power a device puts a processor and a boot sequence in the path of a power function. The LTC4279 does the sequence in hardware, including the two point forced voltage and forced current classification, the short circuit handling and the cable surge protection. That matters in a midspan injector or a small switch where there is no host processor at all, and it matters in a managed switch where the processor should not be able to leave a port in an undefined state after a reset.
Selection notes
- Four point detection rejects a device that only looks like a powered device at two points, which is the common false detection in a rack with several loads on the same cable bundle.
- Dual signature support covers powered devices that present two detection signatures, which is how higher power classes are negotiated on four pair cable.
- The detection backoff timer is for midspan injectors, which have to retry detection on a schedule rather than continuously.
- The plus or minus 80 V rating on the OUT pin covers the surge a cable can couple into the port, so the external clamp is about the standard, not about normal operation.
Questions buyers ask
Does it need a microcontroller for classification? No. Detection, classification and the current limit sequence run in the part, and the status pins report the result.
What sets the maximum port power? The mode selected by the pin strapping and the external MOSFET and sense resistor. The part supports up to 123 W, but the thermal path of the port has to support the mode chosen.
PoE ports are usually quoted with the magnetics and the MOSFET, and allocation on those parts is tracked under component lead time solutions. The rest of the controller family is on the power management cross reference page.
Request Quote — In Stock, 100% New & Original, Full Warranty