Contact Us

LTC3407EMSE#TRPBF

Brand: Analog Devices
Analog Devices LTC3407EMSE#TRPBF is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC3407EMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC3407EMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC3407EMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTC3407EMSE#TRPBF: Two 600 mA Rails at 1.5 MHz From 40 uA of Quiescent Current

The LTC3407 is a dual synchronous step-down regulator with two 600 mA outputs, a fixed 1.5 MHz switching frequency, an input range of 2.5 V to 5.5 V and an output range of 0.6 V to 5 V per channel. Quiescent current with both channels regulating is 40 uA, shutdown current is under 1 uA, and the internal switches are 0.35 ohm with a 1 A peak current rating per channel. Efficiency reaches 96 percent, and the part includes a power-on reset output, a selectable burst mode for light load efficiency and a pulse skipping mode for low ripple.

The two light load modes are not the same product

Burst mode turns the regulator off between groups of pulses, so the quiescent current falls and the efficiency at a milliamp of load stays high, at the cost of an output ripple that carries the burst frequency. Pulse skipping keeps the switching continuous and skips cycles instead, which gives a much quieter output at light load and a lower efficiency. A product that must pass an emissions limit will use pulse skipping; a product that must last a year on a cell will use burst mode. The mode pin selects between them at run time, so the choice can be made per product without changing the bill of materials.

1.5 MHz against the size of the inductor

At 1.5 MHz the switching period is 667 ns, so a 2.2 uH inductor with a 1.8 V output from a 3.3 V input sees a ripple current of about 0.33 A, which is half of the 600 mA rating. A 4.7 uH inductor halves that ripple and doubles the inductance's board area. The trade is not only ripple: the peak current has to stay below the 1 A switch rating during a load step, and a small inductor reaches that limit sooner. The 2.2 uH value in the data sheet's typical application is a compromise between ripple, transient response and footprint, not the only correct value.

ParameterValueWhat it decides
OutputsTwo, 600 mA eachTwo rails from one inductor pair and one part
Input range2.5 V to 5.5 VSingle cell to a 5 V rail
Output range0.6 V to 5 V per channelAdjustable through a feedback divider
Switching frequency1.5 MHz fixed667 ns period, small inductors and capacitors
Switch resistance0.35 ohm0.126 W at 600 mA in each channel
Peak switch current1 A each channelHeadroom above the 600 mA rating
Quiescent current40 uA, both channels0.35 mAh a year in a standby state
Shutdown currentUnder 1 uAA hard off state for shipping
EfficiencyUp to 96 percentLoad dependent, not at light load
Dropout100 percent duty cyclePasses the input through near dropout
Light load modesBurst and pulse skippingRipple against efficiency, selectable at run time
Power-on resetOn chipHolds a processor until both rails are valid
PackageMSOP and 3 mm by 3 mm DFNThe DFN is the thermally better choice

The 0.35 ohm switch at 600 mA

A 0.35 ohm switch carrying 600 mA dissipates 126 mW, and the same current passing through the second channel doubles it. In a 3 mm by 3 mm DFN that is a manageable thermal load, in a 10-lead MSOP it is the limit of the package without copper. The loss also sets the efficiency ceiling before switching loss is counted: at 1.8 V out and 3.3 V in, the ideal duty cycle is 55 percent, so the conduction loss alone is about 5 percent of the delivered power, and the 96 percent figure belongs to a lower duty cycle and a lower current.

Power-on reset and sequencing

The power-on reset output is open drain and asserts until both outputs are within tolerance. In a system with a processor and a radio, that single signal replaces a discrete supervisor and ties the two rails into one release point. Where the two rails have to come up in a defined order, the run pins are the control: releasing them separately gives independent sequencing, and releasing them together gives a common start with no ordering guarantee, which is what a chip that needs the core before the input and output cannot accept.

Buying a dual regulator for a portable product

The three numbers that decide this class of part are quiescent current, peak switch current and the light load mode, and the order code carries the package. A second source part with a lower quiescent current but a fixed burst mode will show up in an emissions test that the original passed. Availability is tracked through power management cross reference, and the wider question of consolidating power rails is set out in vendor consolidation. Where a rail is being replaced under a lead time constraint, the options are in component lead time solutions.