LTC3115EFE-2#TRPBF
Product Specifications
LTC3115EFE-2#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC3115EFE-2#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTC3115-2: 40 V In and 40 V Out, and the Two Amp Rating Depends on the Input
The LTC3115-2 is a synchronous buck-boost converter that accepts 2.7 V to 40 V at the input and produces 2.7 V to 40 V at the output, switching between 100 kHz and 2 MHz, with efficiency up to 95 percent and a no load quiescent current of 30 microamps in burst mode. It is qualified to AEC-Q100 and comes in a 4 by 5 mm dual flat no lead package or a 20 lead thermally enhanced TSSOP. The number that most people read first, the 2 A, is conditional, and reading it as unconditional is the most common way to undersize this part.
Two amps, zero point eight amps, or nothing
| Condition | Output current | Where it comes from |
|---|---|---|
| Step down, input above 6 V | 2 A | The inductor and the high side switch are the limit |
| Step up, 5 V output from a 3.3 V input | 0.8 A | Input current limit, not output switch limit |
| Input below 2.7 V | Not specified | Below the minimum operating voltage |
| Output above 40 V | Not allowed | The same ceiling applies at both ends |
The dash two is about the input, not the output
The suffix marks a version optimised for input voltage transients faster than 1 ms; for slower rails the -1 version is recommended. That is an unusual way to specify a converter and it matters: a board that sees a 40 V automotive load dump with a sub millisecond edge wants this part, and a board with a slowly varying 12 V rail does not need it and may get slightly better behaviour from the other version. Choosing by the output requirement alone gives the right current and the wrong transient response.
Where the losses go at the extremes
At 40 V in and 5 V out the conversion ratio is eight to one, and the part spends most of its time in step down mode, where efficiency is high and the inductor current is small. At 3 V in and 5 V out the ratio is inverted, the current in the inductor is larger than the output current, and the 0.8 A output rating is about the input current limit divided by the boost ratio. Heat is worst at the highest input voltage and the highest output current together, because the switching losses scale with voltage and the conduction losses with current squared.
Burst mode and the noise it brings
The 30 microamp no load quiescent current comes from burst mode operation, which skips switching cycles at light load. That is exactly what a battery powered instrument wants and exactly what a radio does not, because the burst frequency lands in the audio band and the ripple is larger. The mode is pin selectable, so the same converter can serve both, but the choice has to be made before the output filter is sized: a filter that is adequate in forced continuous mode will show several millivolts of low frequency ripple in burst mode.
Replacement and availability
The substitution question for a wide input converter is the input transient requirement first, then the current at the actual operating point, and the package last. A part rated 2 A at 12 V in will not deliver 2 A at 3.3 V in, whatever its front page says, and comparing two parts by their headline current is the usual source of a board that browns out at low battery. The power management cross reference page lists the converter family, the component lead time solutions page tracks allocation, and incoming lots follow the incoming inspection plan.