LTC2249IUH#TRPBF
Product Specifications
LTC2249IUH#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC2249IUH#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC2249IUH#TRPBF: 14 bits at 80 Msps and 222 mW
The LTC2249IUH#TRPBF is a 14-bit 80 Msample per second analog to digital converter in a 32-pin 5 mm by 5 mm QFN, running from a single 3 V supply between 2.7 V and 3.4 V and dissipating 222 mW. Signal to noise ratio is 73 dB and spurious free dynamic range 90 dB for a 70 MHz input, the input accepts 1 V to 2 V peak to peak, full power bandwidth of the sample and hold is 575 MHz, integral nonlinearity is plus or minus 1 LSB typical, and there are no missing codes over temperature. A clock duty cycle stabilizer, shutdown and nap modes are included, and the family is pin compatible across 10 to 125 Msample per second grades. It is listed in the analog and mixed-signal IC line card with the rest of the converter range.
Seventy three dB of SNR is 12.1 effective bits
The resolution is 14 bits, but the noise sets how many of those bits carry information. The arithmetic is worth doing before a specification is written:
| Quantity | Figure | Note |
|---|---|---|
| SNR at 70 MHz input | 73 dB | 12.1 effective bits |
| SFDR at 70 MHz input | 90 dB | the largest spur, not the noise floor |
| One LSB at 2 V peak to peak | 122.1 uV | 16384 codes over the span |
| Transition noise | 1.2 LSB root mean square | 146.5 uV, above one LSB |
| Supply current at 3 V | 74 mA | 222 mW total |
| Output data rate | 140 Mbyte per second | 80 Msample at 14 bits |
| Full power bandwidth | 575 MHz | why a 70 MHz input at 80 Msps works |
A 70 MHz input at an 80 Msample per second rate is undersampling: the signal sits in the second Nyquist zone, between 40 MHz and 80 MHz, and the converter folds it down. That only works because the sample and hold has 575 MHz of full power bandwidth and the clock has low jitter. The effective number of bits falls as the input frequency rises, so the 73 dB figure belongs to the 70 MHz test condition and not to a 5 MHz input.
The digital side is the second engineering problem
Eighty million samples of 14 bits is 140 Mbyte per second, which has to be captured by an FPGA or a receiver without dropping samples. The pin-compatible family covers 10, 25, 40, 65, 80, 105 and 125 Msample per second in both 12-bit and 14-bit versions, so the same board can be built at several rates and the digital interface has to be sized for the fastest one that will ever be fitted.
The clock duty cycle stabilizer matters when the clock source is not a 50 percent duty square wave: without it, the aperture shifts with the duty cycle and the even order distortion rises. The shutdown and nap modes are for a system that samples in bursts rather than continuously.
Selection notes
- The I suffix is the industrial temperature grade. The same die in the commercial grade is a different order code, and the UH suffix is the QFN package.
- A single 3 V supply with a separate output supply lets the digital side drive 0.5 V to 3.6 V logic, so the converter does not force the FPGA bank voltage.
- 1.2 LSB of transition noise means the lowest codes are not stable; a DC measurement with this converter needs averaging, not a single sample.
- 222 mW in a 5 mm QFN is a thermal question when four or eight converters sit on one board, and the exposed pad is the only path.
Questions buyers ask
Can it digitise a 70 MHz signal with an 80 MHz clock? Yes, by undersampling in the second Nyquist zone. The signal is folded to 10 MHz, and the 575 MHz sample and hold bandwidth is what makes that legal.
Is the 14-bit resolution usable? At 12.1 effective bits and 1.2 LSB of transition noise, the bottom two bits are noise. A system that needs 14 bits of dynamic range has to average or to use a lower noise converter.
What should a quote request include? The order code, the input frequency and amplitude, the clock rate and jitter, and the digital interface. Send the BOM line to the converter cross reference for a pin-compatible grade at a different rate, and to the cost reduction desk when a 12-bit member of the same family would meet the specification.
Request Quote — In Stock, 100% New & Original, Full Warranty