Contact Us

LT8610ABIMSE#TRPBF

Brand: Analog Devices
Analog Devices LT8610ABIMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT8610ABIMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT8610ABIMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT8610ABIMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT8610ABIMSE#TRPBF: The B Variant Where Light Load Efficiency Is Nine Points Better

The LT8610ABIMSE#TRPBF is the same 42 V, 3.5 A synchronous step-down converter as the A version, with one documented difference: the AB variant has improved burst mode efficiency, quoted as 91 percent at a 1 mA load against 82 percent for the A version, both at 12 V in and 3.3 V out. The I suffix is the temperature grade that is guaranteed over the whole minus 40 to plus 125 degrees junction range by test, where the E grade is guaranteed from 0 degrees and characterised below it. Everything else is shared: 3.4 V to 42 V input, 30 ns minimum on-time, 2.5 uA quiescent current, 0.97 V reference and a 16-lead MSOP with an exposed pad.

What nine points at 1 mA is worth, and when it is worth nothing

At 1 mA and 3.3 V the output power is 3.3 mW, so 91 percent against 82 percent is an input power of 3.6 mW against 4.0 mW, a difference of 0.4 mW. That sounds negligible until the rail is an always-on housekeeping supply in a product that sleeps for months: 0.4 mW is 3.5 Wh over a year, which is comparable to a small primary cell. In a product that runs at tens of milliamps the difference disappears into the load, and the AB variant buys nothing. The decision is therefore about the load profile and not about the part, and the same reasoning applies to any efficiency figure quoted at a load the product never sees.

Where the gain comes from in burst mode

In burst mode the converter delivers a packet of energy and then sleeps, and the efficiency at light load is dominated by the energy lost in each wake-up rather than by conduction loss. The AB variant reduces the work done per burst cycle, which is why the improvement shows up at 1 mA and not at 1 A. The cost is a slightly different burst behaviour, so the output ripple and the switching spectrum at light load should be checked on the actual board rather than assumed from the A version, particularly in a product that has to meet an emission limit while idling.

ParameterValue on this order codeWhat it decides
Light load efficiency91 percent at 1 mA, 12 V to 3.3 VThe A version is 82 percent in the same test
Temperature gradeI, guaranteed minus 40 to plus 125 degreesFull range tested, not characterised
Input range3.4 V to 42 V24 V and automotive rails directly
Output current3.5 A maximumTwo and a half amps in the original part
Minimum on-time30 nsHigh input to low output at high frequency
Quiescent current1.7 uA in shutdown between bursts2.5 uA total with the recommended divider
Switching frequency200 kHz to 2.2 MHzAdjustable or synchronised to a clock
Power goodWithin plus or minus 9 percentSequencing window is wider than the rail tolerance
Package16-lead MSOP with exposed padMSL and thermal handling both apply

The I grade is the other half of the order code

The temperature letter decides how the part was tested and not what it contains. The E grade is guaranteed from 0 to plus 125 degrees junction, with the colder part of the range assured by characterisation, and the I grade is guaranteed across minus 40 to plus 125 by test, at the same junction temperature limit. For a product specified to start at minus 30 degrees, the I grade is the defensible choice and the cost difference is the price of a guarantee. For an indoor product that never goes below zero, the E grade is the same converter for less money.

Where the part belongs

Battery backed instruments, always-on monitoring equipment, automotive body modules and any rail that spends most of its life at microamp load and occasionally at amps are the sockets where the AB variant earns its price. Where the load never drops below a few milliamps, the A version is equivalent and cheaper. The ADI part second source page sets out the fields a substitute has to match, the pin to pin cross reference covers the MSOP body, and the one stop BOM sourcing page covers the converter with its inductor and capacitors on a single order.

The enable threshold is a real undervoltage lockout, not a logic input

The EN/UV pin has a precise 1 V threshold, which is unusual for an enable input and is what allows the part to set its own undervoltage lockout with two resistors from the input rail. A divider that puts 1 V on the pin at the chosen input voltage holds the converter off below that level, so a 12 V rail that is allowed to sag is protected from being switched at a duty cycle it cannot support. The same pin also takes the converter to 1 uA of input current when it is pulled low, which is the state that matters in a product that has to sit dormant for months. A 1 V threshold with a resistor divider also means the divider draws current continuously, so the two resistors have to be large enough that their own drain is well under the shutdown current the pin is supposed to achieve.