Contact Us

LT3755EMSE-2#TRPBF

Brand: Analog Devices
Analog Devices LT3755EMSE-2#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3755EMSE-2#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3755EMSE-2#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3755EMSE-2#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3755EMSE-2: E Grade, 75 V Output, and the Disconnect FET That Protects a String

The LT3755-2 is the 40 V input, 75 V output LED controller with the improved open LED status pin, and the E grade in this order code is guaranteed from 0 C to 125 C junction with the cold data assured by characterisation. The part drives a low side FET from a 7.15 V internal regulator, senses string current at 100 mV on the high side, and includes a gate driver output for a disconnect FET in series with the string. That last function is the one that decides whether a single failed LED takes out a fixture or is simply reported.

Published values

ParameterValue
Input range4.5 V to 40 V, 40 V absolute maximum
Output voltageup to 75 V
Current sense threshold100 mV full scale, 96 to 103 mV
FB regulation1.250 V typical, 1.220 to 1.270 V
Open LED threshold1.200 V, 50 mV below regulation
Overvoltage threshold1.310 V, 60 mV above regulation
PWM dimming3000 to 1, PWM pin threshold 1.5 V high and 0.4 V low
Switching frequency100 kHz to 1 MHz, 170 ns minimum off time
Gate drive supply7.15 V regulator, 34 mA current limit, 350 mV dropout
Quiescent current1.4 mA typical, 1.7 mA maximum
Shutdown current1 uA maximum
Package and thermal16 lead MSOP, 43 C/W, 125 C maximum junction
GradeE, guaranteed 0 C to 125 C junction

The disconnect FET is protection, not dimming

PWMOUT is a buffered version of the PWM input driven from the internal 7.15 V rail, and its job is to open a FET in series with the string when the feedback pin rises 60 mV above its regulation point. That is an open LED condition: the string current falls, the boost output climbs, and without a disconnect the output runs to whatever the switch and the diode allow while the surviving LEDs absorb the compliance voltage. With the FET in place the string is opened and the converter idles. The pin is specified to be driven either to ground or to the internal rail, which means the external FET has to be a logic level part with a gate that survives 7.15 V.

This is the difference between a fixture that survives one failed LED and a fixture that loses the whole string. It is also the reason the minus 2 part exists: the improved status pin gives a cleaner indication of the same condition to whatever reads it.

E grade, and where 125 C junction comes from

The E part is guaranteed from 0 C to 125 C and the minus 40 C data is assured by characterisation. In a luminaire the ambient is usually the deciding factor rather than the cold end, and the arithmetic is the 43 C/W junction to ambient: at 85 C ambient a 125 C junction allows 40 C of rise, which is 0.93 W. The controller's own 1.7 mA at 40 V is 68 mW, and the gate charge of a 30 nC FET at 400 kHz is about 80 mW, so the package is comfortable. The number that is not comfortable is the FET's own dissipation, which is outside this part and inside the same enclosure.

The 7.15 V rail with its 34 mA current limit is also the ceiling on gate charge at high frequency. A 150 nC FET at 1 MHz needs 45 mA of average gate current, which the regulator cannot supply, so the gate drive collapses and the FET runs in its linear region. That is a failure that looks like a thermal problem and is actually a gate drive budget problem.

3000 to 1 dimming, measured at the right node

Dimming ratio is quoted on the current through the string, not on the PWM duty alone. At 200 Hz, 3000 to 1 is a 1.67 us pulse, and the 170 ns minimum off time is a tenth of it. Whether the current reaches its regulated value inside that pulse depends on the inductor and the switching frequency: at 400 kHz there are 4 switching periods in the pulse, at 1 MHz there are 1.7. Deep dimming at low frequency is therefore the only place the headline number is achieved, and the honest way to specify a fixture is a dimming curve at the actual frequency rather than the ratio on the first page.

The CTRL pin, which spans 0 to 1.1 V for analog dimming, is the other half of the story. Mixing analog and PWM dimming is how a 10000 to 1 range is built in practice: PWM for the bottom decade, analog for the top.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use one stop BOM sourcing to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the E grade the right choice for an outdoor luminaire? If the fixture is specified to start below 0 C, no. The guarantee starts at 0 C and the cold data is characterised, not tested, so a specification that calls for minus 20 C or minus 40 C start needs the I or H grade. For an indoor fixture the E part is the cheaper correct answer.

What happens if the disconnect FET is left out? An open string drives the boost to its maximum output and the overvoltage protection pulls PWMOUT low, which protects the converter but not the string. The remaining LEDs see the full output voltage and usually fail in turn, so the FET is what turns a single failure into a reported single failure.