Contact Us

LT3751EFE#TRPBF

Brand: Analog Devices
Analog Devices LT3751EFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3751EFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3751EFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3751EFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT3751EFE#TRPBF: 125 joules into a 1000 uF capacitor, and the controller never sees the current

The LT3751EFE#TRPBF is an Analog Devices flyback controller for charging a large capacitor to a high voltage set by the transformer turns ratio and three resistors. The supply range is 5 V to 24 V, the integrated gate driver is a 2 A rail-to-rail stage that works down to 4.75 V, and the current sense threshold is 106 mV differential, which sets the peak switch current through one external resistor. Gate drive is clamped internally to 5.6 V or 10.5 V, selected by a pin, so a logic level MOSFET and a standard gate oxide part can both be driven. Overvoltage and undervoltage detection is user settable on both the supply and the transformer primary. Charge, done and fault are open-drain status pins, so a charger can be sequenced by a microcontroller without an external comparator. The vendor states a typical application charges 1000 uF to 500 V in under one second. It is on the analog and mixed-signal IC line card.

The energy number is the whole specification, and it is 125 J

Half of 1000 uF times 500 V squared is 125 J, and the charge moved is 1000 uF times 500 V, or 0.5 C. Delivered in one second that is 125 W of average output power and 0.5 A of average current into the capacitor. From a 24 V input at 85 percent efficiency the supply has to deliver 6.13 A, which is beyond a 24 V 5 A bench supply and is the first thing that surprises a first build. The peak current is set separately: 106 mV across a 10 milliohm sense resistor is 10.6 A, and across 50 milliohm it is 2.12 A.

ParameterVendor figureDerived figure
Capacitor and voltage1000 uF to 500 V in under 1 s125 J, 0.5 C of charge
Average outputsame125 W, 0.5 A for one second
Input at 24 V5 V to 24 V supply range6.13 A at 85 percent for the case above
Current sense106 mV differential threshold10.6 A with 10 milliohm, 2.12 A with 50 milliohm
Gate drive2 A, clamped to 5.6 V or 10.5 V23 percent and 44 percent of a 24 V rail
Output settingtransformer ratio plus three resistorsprimary or secondary side sensing both supported
StatusCHARGE, DONE, FAULT pinsa charging cycle is a handshake, not a fixed timer

Primary side sensing removes the divider that would have to stand off 500 V

Sensing on the primary means the feedback divider sits on the flyback pulse rather than on the output, so no high voltage resistor string is needed and the sense network stays on the low side of the transformer. The cost is that the output voltage is inferred from the reflected waveform, and the leakage inductance spike is part of that waveform, so the sampling instant has to be after the ringing settles. With secondary side sensing the divider carries the full output and the accuracy is set by the divider ratio, at the price of a high voltage resistor and its creepage distance.

Selection notes

  • The 5.6 V clamp suits logic level MOSFETs; the 10.5 V clamp gives lower on resistance with a standard gate part but needs a MOSFET rated for it.
  • The undervoltage lockout on the transformer primary prevents the charger from starting into a partially charged capacitor.
  • The FAULT pin latches after an overvoltage or undervoltage event, so the controller has to be cycled by the CHARGE pin, which is a firmware behaviour and not a hardware one.
  • At 125 W in a 4 mm by 5 mm QFN the thermal path is the exposed pad and the copper under it, and the transformer is the other heat source in the same corner of the board.

Questions buyers ask

Can this charge a capacitor bank of several thousand microfarads? Yes, the limit is the transformer, the switch and the thermal path, not the controller. The time scales with capacitance for the same power.

Is a dedicated charger IC needed for a photoflash capacitor? For a single flash the average power is low and a smaller controller may be enough. This part earns its place when the repetition rate is high enough that the average power reaches tens of watts.

High voltage chargers are usually bought with their transformer and switch as a set, and the substitutions are compared on power management cross reference. Where a full kit is quoted instead of a controller, the options are under BOM shortage recovery.

Request Quote — In Stock, 100% New & Original, Full Warranty