Contact Us

LT3690IUFE#TRPBF

Brand: Analog Devices
Analog Devices LT3690IUFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3690IUFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3690IUFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3690IUFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3690IUFE: what 70 microamps of quiescent current is worth at light load

The LT3690IUFE is the industrial grade of the 36 V, 4 A synchronous step-down regulator, specified from minus 40 to 125 degrees junction in a 26-lead 4 mm by 6 mm QFN. Its distinguishing number is not the 4 A: it is the 70 microamps of quiescent current at 12 V in and 3.3 V out in Burst Mode, with output ripple held below 15 millivolts peak to peak, and a shutdown current under 1 microamp. In a product that spends most of its life at a few hundred microamps, that number decides the battery, and the 4 A rating decides nothing at all.

Published values

ParameterValue
Input voltage3.9 V to 36 V, overvoltage lockout through 60 V transients
Output current4 A maximum
Output voltage0.8 V to 20 V
Quiescent current70 microamps at 12 V in, 3.3 V out, Burst Mode
Burst Mode rippleunder 15 millivolts peak to peak in typical applications
Shutdown currentunder 1 microamp
Switching frequency170 kHz to 1.5 MHz, programmable and synchronizable
Power goodflags when the output reaches 90 percent of the set value
Soft startprogrammable, with output tracking
Package26-lead, 4 mm by 6 mm QFN
Temperature gradeI, junction from minus 40 to 125 degrees
Order codeLT3690IUFE#TRPBF, tape and reel

The arithmetic of a 70 microamp standby

At 12 V in, 70 microamps is 0.84 mW drawn from the source. If the load is 100 microamps at 3.3 V, the output power is 0.33 mW, so the conversion is running at about 39 percent efficiency no matter how good the switching stage is. At 1 mA of load the output is 3.3 mW and the same 0.84 mW of quiescent overhead is 25 percent of the input, which is 75 percent efficiency at best.

That is the argument for a part like this in a battery product: below about 10 mA the quiescent current is the efficiency, and above about 100 mA the switch resistance is. A converter with 1 mA of quiescent current and a 20 milliohm switch would be better at 2 A and eight times worse at 200 microamps, and the two are often compared on the same datasheet page as if one number covered both.

Burst Mode ripple and the things downstream of it

Ripple under 15 millivolts peak to peak sounds harmless until the rail is feeding an analogue front end or a radio receiver. Burst Mode delivers charge in packets at a low repetition rate, so the ripple has a low frequency component that a small ceramic output capacitor does not smooth away, and it sits in the band where a precision amplifier has no supply rejection left.

For a digital rail it is the right mode. For an analogue rail the usual answer is to keep the converter out of Burst Mode with a forced continuous option or a second stage, which costs the light load efficiency back. Deciding which rail is which before the circuit is fixed is cheaper than finding it in a conducted emissions scan.

Power good, soft start and tracking on a 4 A part

The power good flag goes high when the output reaches 90 percent of the programmed value, which is early enough to be useful and late enough to avoid a false release during a soft start. A system that gates a downstream converter on this flag has to account for the remaining 10 percent, because a rail that is 90 percent up is not a rail that a load can be switched onto without a dip.

Soft start and tracking are the same pin, and the tracking mode is what makes the part usable as the second rail in a sequence, where one supply has to follow another rather than arrive at its own rate. Sequencing by enable pins alone leaves a window in which one rail is up and the other is not, and the current that flows through an unprotected interface in that window is the usual reason a board fails on the first power up.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use one stop BOM sourcing to confirm a substitute before it is fitted; how to reduce component cost is the routine for a part that has already stopped shipping.

Two questions buyers ask

How is the E grade different from the I grade? Both are listed from minus 40 to 125 degrees junction in the order table. The difference is in how the limits are guaranteed rather than in the silicon, so a build that needs the temperature limits held in writing over the full range takes the I grade.

Does Burst Mode have to be used? No. It is the mode that delivers the 70 microamp quiescent current. For a rail feeding analogue circuitry that cannot tolerate the burst ripple, forced continuous operation or a second stage is the usual answer, at the cost of the light load efficiency.