LT3680IMSE#TRPBF
Product Specifications
LT3680IMSE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3680IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3680IMSE#TRPBF: MSOP-10E, the Visible Lead and Why Assembly Teams Ask for It
Electrically this is the same 3.5 A regulator as the DFN version: 3.6 V to 36 V in, 95 milliohm switch, 200 kHz to 2.4 MHz, 75 uA burst quiescent, 0.5 uA shutdown, 0.790 V reference, 15 mV burst ripple. What differs is the body. The MSE package is a ten pin MSOP with an exposed pad and leads that come out to the side of the package, and that single physical difference changes the inspection plan, the rework plan and the stencil at the assembly house. Where two order codes are otherwise interchangeable, this is the one that decides which goes on the board.
Published values
| Parameter | Value |
|---|---|
| Package | 10 pin MSOP with exposed pad, pin 11 is GND |
| Grade | I, minus 40 C to 125 C guaranteed |
| Input range | 3.6 V to 36 V |
| Output current | 3.5 A maximum |
| Switch resistance | 95 milliohms |
| Burst quiescent current | 75 uA at 12 V in to 3.3 V out |
| Burst output ripple | Under 15 mV peak to peak |
| Shutdown current | Under 0.5 uA |
| Synchronisation range | 250 kHz to 2 MHz |
| Feedback reference | 0.790 V, output 0.79 V to 30 V |
| Tape and reel | TR suffix, 500 unit reels on some codes |
Visible leads change what the line can check
A gull wing lead produces a solder fillet on the outside of the joint, so an optical inspection machine can see it and a person with a loupe can confirm it. An exposed pad on the underside of a DFN produces no such fillet, so the joint under the pad can only be checked by X-ray or by electrical and thermal test. On a 3.5 A regulator the pad is also the ground return and the heat path, which means a void under it is not a cosmetic defect: it is a 45 K per watt thermal resistance that has just become a 70 K per watt one. That is the reason a line that already runs optical inspection asks for the MSOP body, and the reason a build that cannot afford X-ray should not choose the DFN without another way of proving the pad joint.
Rework is a stencil question, not a hot air question
Removing either package is a hot air job, but replacing them is not the same. The MSOP can be hand soldered lead by lead and inspected afterwards. The DFN has to be placed with paste printed through a stencil, or soldered with a hot plate, and there is no way to see whether it moved during reflow. On a prototype line that distinction is worth more than the board area the MSOP costs, and on a volume line it is worth less, which is why both bodies exist.
The 15 mV burst ripple is the other thing worth holding on to: a rail that is allowed to burst at light load is a rail that can be quiet enough for a downstream converter or an ADC without a second stage, as long as the burst behaviour is understood. Where a product needs the oscillator locked to a system clock, the synchronisation range of 250 kHz to 2 MHz does that. Where the substitute has to be found at short notice, the power management cross reference lists what else does the job, the pin to pin cross reference covers the footprint question, and lead time options is where we look when the reel on the line is running out.
Two questions buyers ask
Can the two bodies be mixed on one build? Not on the same footprint. The pin out is the same in name and order but the land pattern is not, so a board is tooled for one body or the other. Mixing them means two board variants, two sets of stencils and two thermal answers, which is why the choice is normally made once, at the first prototype.
Does burst mode interfere with a sensitive load? The ripple is specified under 15 mV peak to peak and the part draws 75 uA between bursts at 12 V in, so a downstream linear regulator removes what is left. If the load cannot tolerate any burst behaviour at all, the oscillator can be synchronised and the part run continuously, at the cost of the 75 uA figure.