Contact Us

LT3508EUF#TRPBF

Brand: Analog Devices
Analog Devices LT3508EUF#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3508EUF#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3508EUF#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3508EUF#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3508EUF#TRPBF: two 1.4 A step-down channels from a 3.7 V to 36 V input

The LT3508EUF#TRPBF is a dual current mode step-down regulator with both power switches on the die, delivering two independent 1.4 A outputs from an input of 3.7 V to 36 V. The EUF code is the 24-lead 4 mm by 4 mm QFN on tape and reel, E grade, minus 40 C to 125 C, part marking 3508. Each channel has its own feedback, compensation, soft start, tracking and power good pin, and both channels run from one oscillator at opposite phases. That combination is what makes the part useful on a board that needs two rails from one input without two separate converters and two sets of input capacitors.

Published values

ParameterValue
Input voltage3.7 V to 36 V, two separate VIN pins
Output current1.4 A per channel, internal power switches
Output voltageAdjustable down to 800 mV per channel
Switching frequency250 kHz to 2.5 MHz, set by a resistor on RT/SYNC
SynchronisationExternal clock over the full frequency range
Phase relationshipAnti-phase, which halves the input ripple current
Input quiescent current2.5 mA typical, 3 mA maximum, not switching
Shutdown currentBelow 2 uA
SequencingIndependent tracking, soft start and power good per channel
ProtectionCycle by cycle current limit, frequency foldback, thermal shutdown
Package24-lead 4 mm by 4 mm QFN, part marking 3508
GradeE, minus 40 C to 125 C, AEC-Q100 qualified family

The typical application is the specification in practice

The datasheet leads with a 5.6 V to 36 V input producing 3.3 V and 5 V at 1.4 A each, running at 700 kHz, with a 4.7 uF input capacitor, a 6.8 uH inductor and a 22 uF output capacitor on the 3.3 V channel and a 10 uH inductor with a 10 uF output capacitor on the 5 V channel, plus 0.22 uF boost capacitors and 1 nF, 100 pF and 150 pF compensation parts. Those values are worth copying rather than deriving, because the compensation is tied to the 700 kHz operating point and the inductor values are chosen for a specific ripple current. A board that runs the same rails at 2 MHz needs different inductors and different compensation, and the frequency change is not free even though the resistor on RT is the only component that moves.

Anti-phase switching and what it does for the input

Two converters on one input draw pulses at the same instant unless they are deliberately offset, and the input capacitor then has to supply both pulses with a lower duty ratio available to either. Running the channels in anti-phase makes the two pulses interleave, which reduces the root mean square current in the input capacitor and, in the usual case, allows a smaller capacitor for the same ripple. The part synchronises both channels to a single oscillator, so the phase relationship is fixed by the device rather than by two resistor values that can drift apart. This is the single biggest reason to use a dual converter instead of two singles on a 12 V or 24 V input, and it is also why the two channels cannot be run at independent frequencies.

Where the 3.7 V floor becomes the limit

Both channels share the same 3.7 V minimum input, which is set by the gate drive and the boost refresh rather than by the duty cycle alone. A 3.3 V output from a 3.7 V input is a 89 percent duty cycle request, and the datasheet notes that the boost circuit and the minimum off-time put a ceiling on the maximum duty cycle that depends on the programmed frequency. At 250 kHz there is room; at 2.5 MHz there is not. Programs that need 3.3 V from a 3.6 V battery branch at high frequency are outside the intended use, and the same is true of any rail whose input approaches its output within the dropout of the internal switch. The 36 V ceiling covers 12 V and 24 V industrial buses with room for load dump transients, which is the more common duty.

Sequencing two rails on one die

Each channel has a TRACK/SS pin, a PG pin and its own feedback divider, so a 1.2 V core rail can be made to follow a 3.3 V rail with a resistor divider on TRACK/SS rather than with an external sequencer. Power good is an open drain output per channel, which means the second rail can be held off until the first is in regulation, and the whole sequence can be reported to a microcontroller on one or two pins. This is the practical difference between the LT3508 and two discrete converters: the sequencing hardware is already inside the package and does not need to be qualified separately.

Buying and substituting

The same die is offered in a 16-lead TSSOP as the FE code and in the QFN as the UF code, in E, I and H grades, with H reaching 150 C. Moving between the two bodies changes the footprint and the thermal path, and moving between grades changes the temperature claim, which in this family is the whole point of the H part. The matrix is on the power management cross reference, the shortage route for a single line is BOM shortage recovery, and consolidating the switching rails with the linear rails under one supplier is described on one stop BOM sourcing.