Contact Us

LT3094IMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3094IMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3094IMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3094IMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3094IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3094IMSE#TRPBF: a 500 mA negative rail in a 12-lead MSOP

The LT3094IMSE#TRPBF is the industrial grade of a negative low dropout regulator that takes -1.8 V to -20 V in and holds an output anywhere from 0 V to -19.5 V at 500 mA. The part is built around a 100 uA SET pin current with 1 percent initial accuracy, so one resistor from SET to ground sets the output and a second resistor through the same pin sets the current limit. Noise is 0.8 uV RMS across 10 Hz to 100 kHz and 2.2 nV per root hertz spot at 10 kHz, with 74 dB of power supply rejection at 1 MHz. The IMSE suffix is the 12-lead MSOP body in tape and reel, rated -40 C to 125 C at the junction.

Published values

ParameterValue
Input voltage-1.8 V to -20 V
Output voltage0 V to -19.5 V, one resistor on SET
Output current500 mA
Dropout voltage235 mV typical
Output noise0.8 uV RMS, 10 Hz to 100 kHz
Spot noise2.2 nV per root hertz at 10 kHz
Supply rejection74 dB at 1 MHz
SET pin current100 uA, 1 percent initial accuracy
Quiescent current2.35 mA operating, 3 uA in shutdown
Output capacitor10 uF ceramic minimum
Thermal resistance34 C/W junction to ambient, 5.5 C/W to case
Package and grade12-lead MSOP, -40 C to 125 C, tape and reel

Why the negative side costs more attention

Most boards have a positive rail with wide margin and a negative rail that was added late for an amplifier, a laser bias or a bipolar converter front end. On the negative side the pass element sits between the load and a supply that is already below ground, so the reference has to be referred to the negative rail, and the enable, power good and current limit pins all work in that shifted frame. The LT3094 handles this with a rail to rail error amplifier in unity gain. The consequence that matters on a purchase order is that noise, bandwidth, supply rejection and load regulation stay close to constant as the output moves, because the amplifier does not change gain when the SET resistor changes.

What 74 dB at 1 MHz changes in a real BOM

The usual upstream supply for a negative rail is a charge pump or an inverting switcher running between 300 kHz and 2 MHz. A regulator with 74 dB of rejection at 1 MHz removes most of that switching residue without a second LC stage, and the 0.8 uV RMS noise figure is quoted with the recommended capacitor on the SET pin. Two consequences follow for the parts list. The output capacitor can be 10 uF ceramic, so no tantalum is needed, and the input side can stay on the same ceramic the switcher already uses. The VIOC pin is the other half of the story: it drives the upstream regulator so the voltage across the LT3094 stays near a fixed window, which drops the dissipation in the linear stage and keeps rejection high instead of falling off as the input climbs.

MSOP against the DFN body

Both bodies carry the same die and the same electrical table. The MSOP is 34 C/W junction to ambient against 33 C/W for the 3 mm by 3 mm DFN, and 5.5 C/W against 8 C/W to the case, so the thermal difference is small and the choice is usually mechanical. The MSOP has visible leads, which helps in inspection, rework and in assemblies that go through a second hand soldering step. The DFN needs the exposed pad soldered, and on this part the exposed pad is the IN pin, which means the pad is not a quiet ground but the negative input. On a four layer board that is normal. On a two layer board it is the first thing to check, because a pad tied to the wrong net shorts the input to the plane.

Grade and order code

The electrical table is specified over -40 C to 125 C for the E and I grades, -40 C to 150 C for H, and -55 C to 150 C for MP. The I grade differs from E in screening and documentation rather than in the junction limit, so an industrial build that already derates to 110 C will not see a difference on the bench. The TR suffix is tape and reel; TRMPBF is the 500 unit reel offered through some channels. Junction temperature maximum is 150 C on every grade, so the 125 C figure is the range the part is guaranteed over, not the point at which it stops working.

Where this code sits in a sourcing file

The LT3094IMSE#TRPBF is a stocked linear part rather than a long lead item, but the negative rail is exactly the place where a substituted capacitor or a changed upstream switcher quietly ruins the noise number. When a BOM carries this code and the build is moving, the useful check is whether the substitute holds the SET pin current tolerance and the 10 uF minimum, since both are written into the electrical table and both move the output. Buyers matching several ADI and Linear codes on one file can use the power management cross reference to keep the rails grouped, and the ADI part second source notes list what a drop in candidate has to hold. For schedule questions the lead time page shows how the negative rail families are quoted.