Contact Us

LT3094IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3094IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3094IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3094IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3094IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3094IDD#TRPBF: the same negative regulator in a 3 mm DFN

The LT3094IDD#TRPBF is the 3 mm by 3 mm DFN version of the 500 mA negative regulator, industrial grade, supplied in tape and reel. Electrical ratings are the same as the MSOP body: -1.8 V to -20 V in, 0 V to -19.5 V out, 235 mV typical dropout, 0.8 uV RMS noise over 10 Hz to 100 kHz, 74 dB rejection at 1 MHz and a 100 uA SET pin with 1 percent initial accuracy. The DFN brings the junction to case figure to 8 C/W and junction to ambient to 33 C/W, and it removes the leads in favour of an exposed pad that is tied to IN.

Published values

ParameterValue
Input voltage-1.8 V to -20 V
Output voltage0 V to -19.5 V
Output current500 mA
Dropout voltage235 mV typical
Output noise0.8 uV RMS, 10 Hz to 100 kHz
Supply rejection74 dB at 1 MHz
SET pin current100 uA, 1 percent
Quiescent current2.35 mA, 3 uA shutdown
Output capacitor10 uF ceramic minimum
Thermal resistance33 C/W junction to ambient, 8 C/W to case
Package and grade3 mm by 3 mm 12-lead DFN, -40 C to 125 C

The exposed pad is the input, not ground

On a positive regulator the thermal pad is almost always ground, and assembly houses treat it that way by habit. On the LT3094 the pad is the IN pin, so the copper under the body sits at the negative input. That single fact drives the copper decision: the pad wants area for heat, but the area is a negative node, and any ground pour that creeps under the body becomes a short. The clean arrangement is a dedicated copper shape for IN under the part, connected to the input capacitor and to the upstream supply, with the ground plane kept to the other side of the board. The 8 C/W junction to case figure then works as intended, because heat leaves through that pad into copper rather than through the air.

Where the 500 mA goes

At -20 V in and -19.5 V out the part dissipates about 0.25 W plus quiescent, which the DFN handles comfortably on a modest pad. The hard case is the other direction, a -5 V input feeding a -1 V rail at 500 mA, where 2 W lands in the package and the 150 C junction maximum arrives quickly on a small pad. That is the case where the VIOC pin earns its place: it forces the upstream regulator to track the output plus a fixed headroom, so the voltage across the linear stage stays small and the dissipation stays inside the copper. Buyers should treat the 235 mV dropout as a floor to be respected and not as an operating point, because running near it at full current removes the rejection margin the part is bought for.

High speed and converter loads

The applications in the data sheet are RF and precision supplies, very low noise instrumentation, high speed and high precision converters, and post regulation after a switcher. The common thread is a load that draws current in short bursts and does not tolerate a dip. At 500 mA with a 10 uF ceramic output, the regulator loop is fast enough that the output does not move much when a converter starts a conversion, and the 2.2 nV spot noise at 10 kHz stays below the converter's own noise floor in most 16 to 20 bit chains. For a bench check the useful measurement is rejection at the switching frequency of the upstream stage, taken at the load, not at the regulator output pin.

Order code and stock

The IDD suffix is industrial, -40 C to 125 C, and TR is tape and reel. H and MP versions of the same DFN reach -40 C to 150 C and -55 C to 150 C if the board really runs hot. Because this code is a linear regulator with a fixed pinout across the MSOP and DFN bodies, a substitute is easy to fit electrically and easy to get wrong thermally, which is why the pad connection should be confirmed on the assembly drawing before a build. For files that carry several ADI rails, the power management cross reference keeps the negative and positive families separate, and the one stop BOM sourcing page covers consolidated buying across those lines. Quotations for the DFN body follow the same schedule as the MSOP, shown on the lead time page.