Contact Us

LT3092ITS8#TRPBF

Brand: Analog Devices
Analog Devices LT3092ITS8#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3092ITS8#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3092ITS8#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3092ITS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3092ITS8#TRPBF: a 200 mA two terminal current source in an 8-lead SOT-23

The LT3092ITS8#TRPBF is an industrial grade programmable current source that needs two resistors and nothing else. A 10 uA reference flows out of the SET pin, and the ratio of a resistor from SET to the load to a resistor from SET to the input sets the output current, so the same device covers 0.5 mA to 200 mA with a change of two values. Input range is 1.2 V to 40 V, current regulation is better than 10 ppm per volt from 1.5 V to 40 V, and the part needs no input or output capacitor to stay stable. The ITS8 suffix is the 8-lead SOT-23 body in tape and reel, rated -40 C to 125 C.

Published values

ParameterValue
Input voltage range1.2 V to 40 V
Output current0.5 mA to 200 mA, set by two resistors
SET pin current10 uA, 1 percent initial accuracy
Current regulationbetter than 10 ppm per volt, 1.5 V to 40 V
Line regulation0.001 percent per volt typical
Input capacitornot required
Output capacitornot required
Protectionreverse voltage, reverse current, current limit, thermal shutdown
Package8-lead SOT-23, tape and reel
Temperature range-40 C to 125 C, industrial grade
QualificationAEC-Q100 versions available with the W suffix

How two resistors set the current

The relation is I out equal to 10 uA multiplied by RSET divided by ROUT, where RSET sits between the input and the SET pin and ROUT sits between SET and the load. That arrangement makes the output current independent of the voltage across the device, as long as the device has at least 1.2 V across it, which is the compliance the part needs to regulate. For a 20 mA output from a 10 uA reference the ratio is 2000, so 100k and 50 ohm are enough. The reason this matters at the purchasing stage is that the two resistors are the accuracy of the current, not the device alone: a 1 percent SET pin with 1 percent resistors gives a 2 percent source, and a buyer who specifies 1 percent system accuracy needs 0.1 percent resistors on both positions.

No capacitors, and why that is a feature

The part is stable without input or output capacitance, which is unusual for a regulator and is the reason it appears in sensor loops and in circuits that must survive a cable fault. In a two terminal arrangement the device sits in series with a signal line and has high DC and AC impedance, so a long cable's capacitance does not turn the loop into an oscillator. In an intrinsic safety circuit the same property is what allows the source to sit inside the barrier without adding stored energy. For a buyer, the practical effect is a shorter bill of materials and one less lifetime question when a capacitor series changes.

Thermal limits at 200 mA

At the top of the current range the device dissipates the voltage across it multiplied by 200 mA. With 10 V across the part that is 2 W, which an 8-lead SOT-23 cannot hold for long, and the thermal shutdown will cycle. The SOT-23 body is suited to a few hundred milliwatts in still air, so a 200 mA source at high compliance belongs in the DFN or the SOT-223 body. The useful rule for a specification is to state the compliance voltage and the current together, because 200 mA at 2 V across the part is a different product from 200 mA at 20 V across it.

Where it is used

The data sheet lists two terminal floating current sources, ground referred sources, variable sources, in-line limiters and intrinsic safety circuits. Sensor excitation, remote supply over a twisted pair and precision limiting of a locally generated rail are the common cases. All of them want a current that does not change when the load resistance moves, which is exactly what the 10 ppm per volt figure describes. Files that carry this device next to other ADI power parts can be grouped through the power management cross reference, and a substitute should be checked against the ADI second source notes for reference current accuracy and compliance. Reel quantities and schedules appear on the lead time page.