Contact Us

LT3092IST#TRPBF

Brand: Analog Devices
Analog Devices LT3092IST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3092IST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3092IST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3092IST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3092IST: a 200 mA current source that is two resistors and a package

The LT3092IST is the industrial grade of the two-terminal programmable current source in a 3-lead SOT-223 package, specified from minus 40 to 125 degrees junction. It sets an output current anywhere from 0.5 mA to 200 mA with two resistors, works from 1.2 V to 40 V, needs no input or output capacitor to stay stable, and holds its set current to 1 percent initial accuracy with better than 10 parts per million per volt of regulation. It is AEC-Q100 qualified. The SOT-223 is the package that decides how much of the 200 mA is actually usable at high input voltage.

Published values

ParameterValue
Output current0.5 mA to 200 mA, set by two resistors
Input voltage1.2 V to 40 V
Set pin current10 microamps, 1 percent initial accuracy
Current regulationbetter than 10 parts per million per volt
Line regulationunder 0.001 percent per volt typical
Dropout voltage1.22 V typical, 1.45 V maximum at 10 mA
Current limit200 mA minimum, 300 mA typical
Reference noise0.7 microamps rms from 10 Hz to 100 kHz
Ripple rejection90 dB at 120 Hz with 0.1 microfarad on SET and 2.2 microfarad on OUT
Protectionreverse voltage, reverse current, current limit, thermal shutdown
Package3-lead SOT-223
Temperature gradeI, junction from minus 40 to 125 degrees

The set current is 10 microamps, and the ratio does the rest

The output current is the 10 microamp set current plus 10 microamps multiplied by the ratio of RSET to ROUT, so in practice the ratio alone sets the current. A 50 mA source needs a ratio of 5000, which with a 20 kilohm RSET is a 4 ohm ROUT. The 20 kilohm choice is not arbitrary: it puts 200 millivolts across RSET, and that voltage is what keeps the 2 millivolt offset between the SET and OUT pins from dominating the accuracy.

Drop RSET to 2 kilohm, which puts 20 millivolts across it, and the same 2 millivolts of offset is a 10 percent error rather than a 1 percent one. The data sheet says this directly, and it is the single most common reason a breadboarded current source reads wrong: the resistors are the right ratio and the wrong magnitude.

Six watts in a SOT-223, and why the current has to come down

At 200 mA with a 1.5 V drop across the part the dissipation is 0.3 W, which a SOT-223 handles. At 30 V in and 3.3 V out the drop is 26.7 V and the dissipation at 200 mA is 5.3 W, which the package does not. A SOT-223 with a modest copper pad is a few tens of degrees per watt, so 5.3 W is several hundred degrees of rise before the thermal shutdown acts.

The usable current falls as the input rises, and the number that matters is the thermal resistance of the actual pad on the actual board. For a 40 V industrial loop the part is usually run at 10 mA to 20 mA, not because the current capability is missing but because the voltage across it is doing the heating. A series resistor ahead of the source shares that heat for a few cents, and it is the cheapest fix in the whole circuit.

Why a current source wants no capacitors

The part is stable without input or output capacitance, which is unusual enough to be worth saying plainly. In a two-terminal configuration it presents a high impedance at both ends, which is what makes it usable inside an intrinsically safe barrier where stored energy is limited and a capacitor is a liability rather than an improvement.

Adding a small capacitor across RSET lowers the output noise by bypassing the resistor shot noise, and the data sheet gives 0.7 microamps rms from 10 Hz to 100 kHz as the reference figure without it. Adding capacitance changes the impedance the source presents at high frequency, so in an application where that impedance is the point, the capacitor is a trade rather than an upgrade.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, BOM shortage recovery is the check list before a substitute goes in, and how to reduce component cost is how a gap is covered without a new line item.

Two questions buyers ask

Can the LT3092 deliver 200 mA at 30 V in? Not in a SOT-223. The dissipation at 200 mA with a 26.7 V drop is 5.3 W, far beyond what the package can remove. The current has to come down, or the voltage across the part has to be shared with a series resistor.

Why does the accuracy depend on the resistor value and not just the ratio? Because the 10 microamp set current across RSET produces the reference voltage, and the offset between the SET and OUT pins subtracts from it. A 20 kilohm RSET gives 200 millivolts, which makes 2 millivolts of offset a 1 percent error; a 2 kilohm RSET gives 20 millivolts and the same offset becomes 10 percent.