LT3091EDE#TRPBF
Product Specifications
LT3091EDE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3091EDE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3091EDE#TRPBF: extended grade 1.5 A negative regulator with cable drop compensation
The LT3091EDE#TRPBF is the extended grade of the 1.5 A negative regulator in the 14-lead DFN, tape and reel, rated -40 C to 125 C. It shares the family table: 1.5 V to 36 V input, 0 V to 32 V rail to rail output, 300 mV typical dropout at 1.5 A, 18 uV RMS noise over 10 Hz to 100 kHz, a 50 uA SET reference at 1 percent, a 1.2 mA quiescent current that falls below 1 uA in shutdown, and stability with a 10 uF ceramic or tantalum output capacitor. The feature that separates this family from a plain negative regulator is the programmable current limit plus the positive or negative current monitor.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.5 V to 36 V |
| Output voltage | 0 V to 32 V |
| Output current | 1.5 A |
| Dropout voltage | 300 mV typical |
| Output noise | 18 uV RMS, 10 Hz to 100 kHz |
| SET pin current | 50 uA, 1 percent |
| Load regulation | 1.2 mV, 1 mA to 1.5 A |
| Current monitor | 0.25 mA per amp sourced, 0.5 mA per amp sunk |
| Output capacitor | 10 uF minimum, ceramic or tantalum |
| Package and grade | 14-lead DFN, -40 C to 125 C, tape and reel |
Cable drop compensation on a negative rail
When a supply feeds a load at the end of a cable, the current in the cable raises or lowers the voltage at the load, and a regulator that senses at its own output cannot see it. This family carries a cable drop compensation function, which feeds a fraction of the load current back into the SET node so the output rises to cancel the cable loss. On a negative rail the sign of that correction is the part that usually gets wired wrong on a first article, because the compensation has to push the output further from ground, not closer to it. A first article check should measure the voltage at the load, not at the connector.
Current monitor without a shunt
The monitor pin reports load current as a current rather than a voltage, either sourcing 0.25 mA per amp or sinking 0.5 mA per amp depending on the configuration. A single resistor to the appropriate rail converts that into a voltage for an ADC, and the same signal can drive a comparator for an overcurrent flag. For a buyer the useful consequence is that the board does not need a shunt in the negative return, which is where a shunt is most awkward to place and most likely to disturb the ground reference of an analog front end.
Where the grade matters
The E and I grades cover -40 C to 125 C, H covers -40 C to 150 C and MP covers -55 C to 150 C. The E grade is the usual choice for industrial instruments and telecom line cards, where the local ambient inside the enclosure settles in the 60 to 80 C band and the junction stays inside 125 C with a modest copper shape. Moving to H buys 25 C of junction headroom for a small price step, and it is the right move when the board sits next to a power stage or inside a sealed box.
Ordering notes
The EDE suffix is the extended grade DFN with tape and reel. TSSOP, TO-220 and DD-Pak bodies carry the same electrical table for builds that need them, and the TO-220 version is the one usually chosen for a bench or a retrofit where the board cannot take a DFN. For files that carry several negative rails, our power management cross reference keeps the bodies and grades visible, the vendor consolidation page explains grouping the order, and the component cost page covers the volume levers on this family.