Contact Us

LT3090IDD#PBF

Brand: Analog Devices
Analog Devices LT3090IDD#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3090IDD#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT3090IDD#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3090IDD#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3090IDD#PBF: tray quantity for prototype and low volume builds

The LT3090IDD#PBF is the same 600 mA negative regulator as the taped version, in the 10-lead 3 mm by 3 mm DFN, industrial grade, supplied in trays rather than on a reel. The electrical table is unchanged: -1.5 V to -36 V input, 0 V to -32 V output from a single SET resistor, 50 uA SET current with 1 percent initial accuracy, 300 mV typical dropout at 600 mA, 18 uV RMS noise, 85 dB rejection at 120 Hz and a 4.5 uA shutdown current. The tray is the practical unit when the quantity is below a reel and the assembly is done by hand or on a short-run line.

Published values

ParameterValue
Input voltage-1.5 V at 100 mA up to -36 V
Output voltage0 V to -32 V
Output current600 mA
Dropout voltage300 mV at 600 mA typical
SET pin current50 uA, 1 percent
Quiescent current in shutdown4.5 uA typical
Output noise18 uV RMS, 10 Hz to 100 kHz
Ripple rejection85 dB at 120 Hz, 20 dB at 1 MHz
Thermal resistance33 C/W junction to ambient, 8 C/W to case
Package10-lead DFN, tray, -40 C to 125 C

Tray against reel, what it costs on the line

A tray of DFN parts cannot be loaded into a tape feeder, so a line that runs the taped code has to stop and either hand place the tray parts or move them into a spare reel. For ten boards this is fine. For a pilot run of two hundred it is a scheduling problem, and the usual answer is to order the taped code in the reel quantity that the feeder accepts and keep the tray code for the rework bench. The silicon is identical, so a mixed inventory does not create two configurations and does not need two sets of inspection criteria.

Why the DFN is chosen at all

The 10-lead DFN saves roughly half the board area of the 12-lead MSOP and removes the lead frame from the heat path, which matters when several rails sit side by side. The cost is that every connection is under the body, so the only way to inspect the joints is X-ray or a careful look at the meniscus on the pad edges. For a negative regulator that also needs the pad isolated from ground, a hand-built prototype is the stage where the isolation is easiest to fix. That is the main reason the tray code stays in the catalogue: it is what a lab buys before the reel arrives.

Reading the current from a negative rail

The IMONP and IMONN pins carry a scaled copy of the output current, one on the positive side and one on the negative side of the pass element. With a resistor to ground the IMONP pin gives a positive voltage proportional to the load, and the IMONN pin gives a negative one, so a system can pick whichever direction suits its ADC. The scaling is fixed by the part rather than set by the user, which is a benefit in production because there is no calibration step and one gain figure covers every board. For a battery-backed instrument this is often the only current measurement in the negative branch.

Order code and stock

The PBF suffix in this code is the tray, and the same body in tape and reel is IDD#TRPBF. Buyers should not order the tray code for a line that needs a feeder, and should not order the reel for a lab that places by hand. Where the requirement is a wide temperature window rather than the smallest body, the HDD and MPDD codes extend the junction to 150 C in the same footprint. The lead time page carries the current schedule for both pack forms, BOM shortage recovery covers moving between them during a shortage, and the ADI second source page covers the grade changes that need no board revision.