Contact Us

LT3090EDD#TRPBF

Brand: Analog Devices
Analog Devices LT3090EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3090EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3090EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3090EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3090EDD#TRPBF: cable drop compensation in a 3 mm DFN

The LT3090EDD#TRPBF is the extended grade of the 600 mA negative regulator in the 10-lead 3 mm by 3 mm DFN, on tape and reel. Beyond the usual negative regulator specification of -1.5 V to -36 V in, 0 V to -32 V out and 50 uA SET current, this part brings out a programmable cable drop compensation function that lets the output at the regulator sit slightly low so that the voltage at the far end of a cable lands on the target. That matters for negative rails that feed a remote sensor or a camera head over a metre or more of wire, where the lead resistance is a real part of the error budget.

Published values

ParameterValue
Input voltage-1.5 V to -36 V
Output voltage0 V to -32 V, one resistor on SET
Output current600 mA, programmable limit
Cable drop compensationProgrammable, follows the load current
Dropout voltage300 mV typical at 600 mA
Output noise18 uV RMS, 10 Hz to 100 kHz
Ripple rejection85 dB at 120 Hz, 50 dB at 10 kHz
Thermal resistance33 C/W junction to ambient, 8 C/W to case
Package and grade10-lead DFN, -40 C to 125 C, tape and reel

The error the compensation removes

A 0.5 square millimetre conductor at 20 metres has roughly 0.7 Ohm of resistance. At 300 mA the drop along one leg is 0.21 V, and on a two-wire run the round trip means the load sees 0.42 V less than the regulator delivers. No regulator can fix that from its own output pin, because the error appears after the pin. Compensation works by raising the output as the current rises, using the internal current information rather than a remote sense lead, which means no extra wire to the load and no risk of an open sense line driving the output to a rail. For a negative rail the same idea applies with the sign flipped, and the effect is that the load sees a flat voltage over the whole load range.

Setting the compensation without a bench iteration

The compensation is set by a resistor, and the value is chosen from the cable resistance and the full-scale current: the voltage to be added at full load is the current times the round trip resistance, and the resistor is scaled to produce exactly that. Because the correction is proportional to the actual current, a light load gets almost no offset, which is the behaviour a remote sensor needs. The check that matters in production is a two-point measurement, one at 10 percent load and one at full load, at the far end of the cable rather than at the connector, because a measurement at the regulator pin will always look correct.

DFN thermals with the pad on IN

The exposed pad on this body is the IN pin, so the copper under the part is a negative node and the ground plane has to be kept away from it. With the pad soldered to a dedicated shape, junction to case is 8 C/W and the end to end figure on a 2500 square millimetre shape is 33 C/W. A 1 W dissipation therefore runs about 33 C above the surrounding copper, which is acceptable in a cabinet at 60 C but not in one at 95 C. Buyers should ask for the copper area on both sides of the board, since the back side copper is what actually spreads the heat in a small enclosure.

Order code and stock

EDD is the extended grade DFN on tape and reel, IDD is the industrial grade of the same body, and EMSE is the MSOP equivalent. The compensation pin and the monitor pins are present on all of them, so moving between bodies keeps the function set and changes only the copper. Files that carry a remote sensor on a negative rail usually need the compensation and the current monitor together, and the power management cross reference keeps those two features mapped across the family. Consolidated buying is covered on the one stop BOM page, and reel scheduling is on the lead time page.