Contact Us

LT3088MPST#TRPBF

Brand: Analog Devices
Analog Devices LT3088MPST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3088MPST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3088MPST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3088MPST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3088MPST#TRPBF: the minus 55 C grade of the 800 mA rugged regulator

The LT3088MPST#TRPBF is the widest temperature grade of the 800 mA single resistor linear regulator, in the 3-lead SOT-223 body, tape and reel. The MP grade is specified from -55 C to 150 C, which is 15 C wider at the top than the industrial version and 40 C wider at the bottom. The electrical content is the family standard: input 1.2 V to 36 V, output adjustable from 0 V to 34.5 V with one resistor, a 50 uA SET pin reference at 1 percent initial accuracy, 27 uV RMS output noise, under 1 mV of typical load regulation that does not change with the programmed output, and 0.001 percent per volt of line regulation. The part is stable with or without input and output capacitors.

Published values

ParameterValue
Input voltage1.2 V to 36 V
Output voltage0 V to 34.5 V, one resistor on SET
Output current800 mA
SET pin current50 uA, 1 percent initial accuracy
Output noise27 uV RMS
Load regulationunder 1 mV typical, independent of output voltage
Line regulation0.001 percent per volt typical
Input and output capacitorsstable with or without
Protectionreverse battery, reverse current, current limit, thermal limit
Package3-lead SOT-223, tape and reel
Temperature range-55 C to 150 C, MP grade

What the minus 55 C floor is for

Most commercial and industrial parts stop at -40 C, which is enough for a warehouse or an outdoor cabinet in a temperate climate. The MP grade exists for equipment that starts cold, including vehicles in northern winters, cold rooms, and outdoor telecom cabinets with no heater. At -55 C the concern is not only the reference but the start up behaviour and the solder joint stress over repeated cold cycles. A buyer specifying this grade should check that the rest of the rail, the capacitors in particular, also carries a cold rating, because a -55 C regulator feeding a -40 C electrolytic is a qualification that fails elsewhere.

The extended safe operating area

The headline feature of this family is an extended safe operating area, which is the region where the pass transistor can carry current while the voltage across it is large. That matters in an all surface mount supply that drops 24 V to 3.3 V at a few hundred milliamps, where a conventional regulator would be limited to a much lower current at the same voltage. The device also withstands reverse input and reverse output to input voltages without reverse current flow, which is the condition that kills simple three terminal regulators when a large output capacitor holds the output up while the input collapses. In an industrial build that shares a 24 V bus between several boards, that reverse condition is a real event rather than a data sheet curiosity.

SOT-223 thermal reality

The SOT-223 body has a tab that is the output on this device, so the copper under the tab is the regulated rail and not ground. At 800 mA with a 3 V drop across the part the dissipation is 2.4 W, which a SOT-223 cannot hold in still air for long; the tab copper has to be generous and the ambient inside the box has to be known. In practice this part is chosen at 800 mA for low dropout applications, and at higher input to output differences the current is derated. The DD-Pak and the 8-lead DFN versions of the same device exist for builds that need more thermal mass in the same footprint family.

Ordering and substitution

The MPST suffix is the MP grade in the SOT-223 body, tape and reel. E, I and H versions of the same body cover narrower windows and are the usual choice when the cold start is not a requirement, and the DD-Pak body covers the same grades with a different thermal path. Because this part is a pin compatible upgrade to the LT1117 family, buyers often meet it during a legacy board revision, and the SET resistor has to be recalculated rather than copied from the older fixed output device. Our power management cross reference lists the grades and bodies, the ADI second source notes cover what a substitute must hold, and the lead time page shows current schedules.