Contact Us

LT3086MPFE#TRPBF

Brand: Analog Devices
Analog Devices LT3086MPFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3086MPFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3086MPFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3086MPFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3086MPFE#TRPBF: 2.1 A at 40 V, minus 55 C to 125 C, in a TSSOP

The LT3086MPFE#TRPBF is the wide temperature grade of a 2.1 A low dropout regulator that takes 1.4 V to 40 V on the input and holds an output anywhere from 0.4 V to 32 V, set by one resistor. The MP code is rated -55 C to 125 C at the junction and comes in the 16-lead TSSOP on tape and reel. On this family the MP grade does not extend the hot end: the H grade is the one that reaches 150 C, while MP pays for the cold end and stops at 125 C, a detail that catches people who assume the letters always run in order.

Published values

ParameterValue
Input voltage1.4 V to 40 V, 1.55 V guaranteed at 2.1 A
Output voltage0.4 V to 32 V, one resistor on SET
Output current2.1 A
Dropout voltage330 mV typical at 2.1 A, 415 mV maximum
AccuracyPlus or minus 2 percent over line, load and temperature
Current monitorIMON equals load current divided by 1000
Output noise40 uV RMS, 10 Hz to 100 kHz at 5 V out
GND pin current1.2 mA at no load
Thermal resistance25 C/W junction to ambient on 2500 square millimetres of copper
Package and grade16-lead TSSOP, -55 C to 125 C, tape and reel

The cold end is the hard end here

At -55 C the SET pin current and the reference voltage both sit at the edge of their windows, and the 400 mV reference is specified 388 mV to 408 mV over the range rather than the 392 mV to 408 mV that applies below 125 C. That 4 mV difference is about 1 percent of the output, and it appears in the same place as the resistor tolerance, so an error budget should read the two columns separately instead of taking the room temperature number and doubling it. Equipment for outdoor cabinets in northern regions is the usual consumer of this code.

2.1 A through a TSSOP

The 16-lead TSSOP with its exposed metal has 10.5 square millimetres of thermal pad underneath, and the measured junction to ambient figure is 25 C/W on 2500 square millimetres of topside copper, rising to 33 C/W when that area falls to 100 square millimetres. At 2.1 A with a 1 V differential the part dissipates 2.1 W plus the quiescent term, so the rise is 55 C on a generous board and 72 C on a small one. In a 70 C cabinet the second case fails on a 125 C part, which is the arithmetic that pushes people to the DD-Pak version of the same die rather than to a higher grade.

Cable drop compensation with a 2.1 A load

At 2.1 A even a short run of thin wire produces a significant drop, so the LT3086 includes a programmable cable drop compensation pin that raises the output as the load current rises. The same current signal feeds the monitor output, which is the load current divided by 1000, and a thermal monitor pin whose voltage tracks the junction and can be used to program an external thermal limit. For a buyer the practical consequence is that a single part number covers the regulation, the current telemetry and the thermal warning, which removes two small parts and a temperature sensor from the list.

Order code and stock

MPFE is the wide temperature TSSOP on tape and reel; EFE and IFE are the standard temperature grades of the same body, and HFE is the one that goes to 150 C. All four are the same die and the same pinout, so a change of grade is a label change and not a board change. The power management cross reference maps the grades across the family, the lead time page carries the TSSOP schedule, and vendor consolidation covers keeping several regulators on one supplier line.