Contact Us

LT3085IMS8E#TRPBF

Brand: Analog Devices
Analog Devices LT3085IMS8E#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3085IMS8E#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3085IMS8E#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3085IMS8E#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3085IMS8E#TRPBF: 500 mA with a separate control supply

The LT3085IMS8E#TRPBF is the industrial grade of a 500 mA low dropout regulator in the 8-lead MSOP with an exposed pad, supplied on tape and reel. The part has two supply pins: IN carries the load current and VCONTROL powers the internal circuitry, which lets the regulator hold 275 mV of dropout even when the input is close to the output. Output is set by a single resistor from the SET pin to ground, using a 10 uA reference current, and it can be brought all the way to 0 V.

Published values

ParameterValue
Input voltage1.2 V to 36 V
Control supplySeparate VCONTROL pin, 1.2 V to 36 V
Output voltage0 V to 36 V, one resistor on SET
Output current500 mA
SET pin current10 uA, 9.9 to 10.1 uA at 25 C
Dropout voltage275 mV in two supply operation
Minimum load current300 uA typical, 500 uA maximum
Ripple rejection90 dB at 120 Hz
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal resistance55 to 65 C/W junction to ambient depending on copper
Package and grade8-lead MSOP with exposed pad, -40 C to 125 C, tape and reel

What the second supply pin changes

In a conventional linear regulator the internal circuitry is powered from the input, so the input has to stay a few hundred millivolts above the output for the loop to work. Splitting the supplies lets VCONTROL sit at a higher voltage, for example 5 V or 12 V, while IN tracks the output closely and only has to carry the load current. The result is a dropout of 275 mV at 500 mA, which is the difference between regulating a 1.2 V rail from 1.5 V or losing it. The cost is one more supply to route and one more decoupling capacitor, which is why the single supply mode also exists: tie IN and VCONTROL together and the part behaves like an ordinary regulator with a larger dropout.

The control current is not negligible

The current drawn by VCONTROL scales with the output current, at about 1.7 percent of it, so at 500 mA the control pin takes 8.5 mA. That current is dissipated inside the package on top of the load path, and it is the reason the MSOP carries a thermal pad. For a 1.5 V to 1.2 V conversion at 500 mA the pass element contributes 150 mW and the control path adds about 30 mW at 5 V, which the 55 C/W body handles easily. At 12 V on VCONTROL the same load puts 90 mW into the control path, and the arithmetic is worth doing before choosing the higher rail.

The pad is the output

The exposed pad on this package is connected to the output, not to ground, so the copper under the body carries the regulated rail. That is convenient for two reasons: the pad can double as a low impedance connection to the output capacitor, and heat leaves the die into the same copper that carries the current. It is a problem if the copper shape is also used as a ground pour or if a plane under the part is at ground. Buyers moving a board between this part and a ground-pad regulator should confirm the pad connection on the assembly drawing.

Order code and stock

IMS8E is the industrial MSOP on tape and reel, EMS8E the extended grade of the same body, and EDCB the 6-lead 2 mm by 3 mm DFN. The MP grade of the MSOP reaches -55 C to 125 C. All versions share the 10 uA SET current and the two supply pins, so the surrounding parts do not change with the body. The power management cross reference maps the family, the one stop BOM page covers ordering the SET resistor and capacitors with the regulator, and vendor consolidation covers keeping the ADI rails on one schedule.