Contact Us

LT3085EMS8E#TRPBF

Brand: Analog Devices
Analog Devices LT3085EMS8E#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3085EMS8E#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3085EMS8E#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3085EMS8E#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3085EMS8E#TRPBF: extended grade, single or dual supply, 500 mA

The LT3085EMS8E#TRPBF is the extended grade of the 500 mA regulator in the 8-lead MSOP with an exposed pad, taped and reeled and rated -40 C to 125 C. The part can run from one supply or from two, and the choice is made on the board rather than at the order desk: tie IN and VCONTROL together for a conventional regulator, or hold VCONTROL higher and let IN track the output for 275 mV of dropout. Output is set by one resistor, using a 10 uA SET current with 1 percent initial accuracy, and it can go down to 0 V.

Published values

ParameterValue
Input voltage1.2 V to 36 V
Control supplyMust sit 1.2 V to 1.35 V above the output
Output voltage0 V to 36 V
Output current500 mA
SET pin current10 uA, 1 percent initial
Control pin currentAbout 1.7 percent of the output current
Minimum load current300 uA typical, 500 uA maximum
Ripple rejection90 dB at 120 Hz
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal resistance55 C/W on 2500 square millimetres of copper
Package and grade8-lead MSOP with exposed pad, -40 C to 125 C, tape and reel

One supply or two, decided by the rail above

In single supply mode the part behaves like any adjustable regulator: the input has to stay above the output by the dropout, which rises with load, and the dissipation is the full input to output differential. In two supply mode the input only has to be 100 to 500 mV above the output while VCONTROL supplies the internal bias, so the pass element dissipates far less and the dropout falls to 275 mV. The trade is that VCONTROL has to be a higher rail, and the current it draws, about 1.7 percent of the output current, is dissipated in the package. At 500 mA that is 8.5 mA, which on a 5 V control rail is 42 mW, and on a 12 V control rail is 102 mW.

Reading the 90 dB rejection figure

The 90 dB figure is quoted at 120 Hz with a 0.5 V peak to peak ripple, a 0.1 uF capacitor on SET and 2.2 uF on the output, and it applies to the control supply path. It is the number that matters when the regulator follows a transformer and a rectifier, where the residual ripple is at twice the line frequency. Above a few kilohertz the figure falls, so a rail that follows a switching converter needs the rejection at the switching frequency, which is a different and lower number. For post regulation after a switcher, the useful measurement is taken at the load with a scope probe, not from the data sheet curve.

The minimum load rule

The part needs 300 uA typical, 500 uA maximum, of load to stay in regulation, because the SET current and the internal bias have to flow somewhere and they flow into the output. A board that can be put into a sleep state with the load disconnected will see the rail drift up. The usual fix is a permanent bleeder resistor sized for 1 mA at the nominal output, which on a 3.3 V rail is 3.3 kOhm and dissipates 3 mW. That resistor should be on the parts list from the first revision, because it is easy to leave out and hard to add after the board is in a housing.

Order code and stock

EMS8E is the extended grade MSOP on tape and reel, IMS8E the industrial grade of the same body, EDCB the 6-lead DFN and MPMS8E the -55 C version. The die and the pinout are shared across the MSOP codes, so a grade change is a label change. The power management cross reference lists the family, the lead time page carries the MSOP schedule, and the BOM shortage recovery page covers moving between grades during an allocation.