Contact Us

LT3083IQ#PBF

Brand: Analog Devices
Analog Devices LT3083IQ#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3083IQ#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT3083IQ#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3083IQ#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3083IQ#PBF: industrial 3 A regulator, 5-lead DD-Pak

The LT3083IQ#PBF is the industrial grade of the 3 A regulator in the 5-lead DD-Pak, lead free finish, specified from -40 C to 125 C. The family table applies: 1.2 V to 23 V input on this body, output from 0 V to 23 V set by one resistor on the SET pin, 50 uA reference at 1 percent, 310 mV dropout, 40 uV RMS noise, under 1 mV of load regulation, 1 mA minimum load and 10 uF of ceramic output capacitance for stability. The pass transistor collector is brought out, which is what allows the low dropout figure when the device is used with more than one supply.

Published values

ParameterValue
Input voltage1.2 V to 23 V
Output voltage0 V to 23 V
Output current3 A
Dropout voltage310 mV
Output noise40 uV RMS, 10 Hz to 100 kHz
SET pin current50 uA, 1 percent
Load regulationunder 1 mV
Line regulation0.001 percent per volt
Minimum load current1 mA
Output capacitor10 uF ceramic minimum
Package5-lead DD-Pak, lead free
Temperature range-40 C to 125 C

The collector pin and two supply operation

Bringing the collector out is unusual in a three terminal regulator and it is the mechanism behind the 310 mV dropout. With a separate, higher control supply the pass transistor can be driven from a rail above the main input, so the regulator keeps regulating when the input is only a few hundred millivolts above the output. That is how a 1.2 V rail is held from a 1.5 V input at 3 A in a server or a telecom card where the intermediate bus has little margin. The cost is a second supply on the board, and the buyer should expect that in the drawing review, because a part with a single input cannot do the same job.

Paralleling for more current or less heat

The data sheet notes that outputs may be paralleled to raise current or spread heat. Because the reference is a current source, two devices share a common SET resistor and each contributes according to its own offset, which keeps the sharing reasonable without an external ballast in most cases. The practical use is thermal: 3 A in one DD-Pak on a small board runs hot, and two devices sharing 1.5 A each spread the heat across two areas. For a buyer the implication is a change in the bill of materials rather than a change in the board intent, and the second device is cheaper than a bigger package with a heatsink.

Where the industrial grade fits

Most telecom, industrial and instrumentation boards run the local ambient between 40 and 70 C, and the industrial grade at 125 C junction covers that with derating. The H grade extends to 150 C and the MP grade starts at -55 C, and both are specified on the same table. A buyer who has been using the MP grade everywhere to be safe should check the price difference, because the volume code is the industrial one and the wide temperature versions are quoted at a premium.

Ordering

IQ is the industrial grade in the DD-Pak with lead free finish, supplied in tubes. TSSOP and DFN bodies of the same device exist for builds that cannot take a tabbed package, and the TO-220 version is still available for retrofits and bench supplies. Our power management cross reference lists the bodies and grades, the one stop BOM sourcing page covers consolidation across the power section, and the component cost page sets out the volume levers.