Contact Us

LT3082IST#TRPBF

Brand: Analog Devices
Analog Devices LT3082IST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3082IST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3082IST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3082IST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3082IST#TRPBF: 200 mA in a three lead SOT-223

The LT3082IST#TRPBF is the industrial grade of a 200 mA low dropout regulator in the 3-lead SOT-223, supplied on tape and reel and rated -40 C to 125 C. The three leads are input, output and SET, with the tab connected to the output, so the part has no shutdown pin and no control supply: it is a two terminal style regulator with a resistor setpoint. Output can be programmed from 0 V to 38.5 V using a 10 uA SET current, and the part is stable with only 2.2 uF of ceramic capacitance on the output.

Published values

ParameterValue
Input voltage1.2 V to 40 V
Output voltage0 V to 38.5 V, one resistor on SET
Output current200 mA
SET pin current10 uA, 1 percent initial accuracy
Load regulationUnder 1 mV typical
Line regulationUnder 0.001 percent per volt typical
Ripple rejection90 dB at 120 Hz, 75 dB at 10 kHz, 20 dB at 1 MHz
Output noise33 uV RMS, 10 Hz to 100 kHz
Minimum output capacitor2.2 uF ceramic
Minimum load current0.5 mA
Thermal resistance20 C/W junction to ambient on 2500 square millimetres
Package and grade3-lead SOT-223, -40 C to 125 C, tape and reel

Twenty degrees per watt is why this body survives

The tab of a SOT-223 is a large solderable surface, and with 2500 square millimetres of copper the junction to ambient figure is 20 C/W, which is better than either DFN in the family. At 200 mA with a 5 V to 3.3 V conversion the dissipation is 340 mW, so the rise is under 7 C. Even at the worst case of 40 V in and 3.3 V out, where the part would dissipate 7.3 W and destroy itself, the thermal figure makes the limit obvious before the board is built. The practical operating envelope is a few hundred milliwatts, and inside that envelope this is the most forgiving package in the family.

Reverse battery and reverse current

The LT3082 withstands a reverse input voltage and a reverse output to input voltage without a reverse current path, which matters in equipment that can be connected backwards or that has a large output capacitor holding a voltage after the input collapses. Most regulators need a diode across the output for this, and the diode costs a part and a volt of headroom. On this part the protection is internal, so a board that is powered from a removable connector can drop the diode and keep the 200 mA rating intact.

No shutdown lead, and what that means

With only three leads there is no enable input, so the rail comes up with the input and goes down with it. For a system that needs a controlled sequence, the switch belongs on the input side, either in the upstream converter or in a load switch. That is a real constraint and it should be checked against the power sequencing requirement before this body is chosen. Where sequencing is not needed, the three lead part is the simplest thing that can regulate, and it is the cheapest way to add a quiet rail to an existing board.

Order code and stock

IST is the industrial grade in tape and reel, EST the extended grade of the same body, and MPST the -55 C to 125 C version, which is only available in this package. The 8-lead SOT-23 and the 8-lead DFN versions add pins and drop the thermal figure, so the SOT-223 remains the choice when dissipation matters. The power management cross reference maps the three bodies, the one stop BOM page covers ordering the SET resistor with the part, and ADI part second source lists the grades that move without a board change.