Contact Us

LT3080IMS8E#TRPBF

Brand: Analog Devices
Analog Devices LT3080IMS8E#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080IMS8E#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080IMS8E#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080IMS8E#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080IMS8E#TRPBF: 1.1 A regulator in the 8-lead MSOP with the pad on the output

The LT3080IMS8E#TRPBF is the I grade of the LT3080 in the 8-lead MSOP with an exposed pad, taped and reeled. It is the middle of the three surface mount bodies: 60 C/W junction to ambient and 10 C/W junction to case, against 55 and 15 for the SOT-223 and 30 and 3 for the DD-Pak. It keeps the separate VCONTROL pin, so the 350 mV dropout figure applies, and it holds the whole family behaviour: 1.2 V to 36 V input, output adjustable from zero to 36 V by one resistor, 1.1 A, 40 uV RMS of noise, and current limit with foldback.

Published values

ParameterValue
Input voltage1.2 V to 36 V, VCONTROL separate
Output voltage0 V to 36 V, one resistor on SET
Output current1.1 A, 1.4 A typical current limit
SET pin current10 uA, 1 percent initial, 9.8 to 10.2 uA over temperature
VIN dropout350 mV at 1.1 A typical, 500 mV maximum
VCONTROL dropout1.35 V at 1.1 A typical, 1.6 V maximum
Output offsetplus or minus 2 mV on this package
Minimum load300 uA typical, 1 mA maximum
Output noise40 uV RMS without a bypass capacitor
Thermal resistance60 C/W junction to ambient, 10 C/W to case
Package8-lead MSOP, exposed pad is OUT, pin 9

Why the offset is better here than on the SOT-223

The output offset specification is plus or minus 2 mV on the DFN and MSOP bodies and plus or minus 5 mV on the SOT-223, DD-Pak and TO-220. The difference is bond wire and lead frame resistance in the current path, not a different die, and it matters when two devices are paralleled: the ballast resistor only has to absorb the offset between the SET pin and the output, so 2 mV allows a smaller resistor and wastes less headroom than 5 mV does. With 10 mOhm of trace per device the vendor reports better than 80 percent sharing, and that figure is easier to hit on the tighter offset part. A board that plans to parallel two regulators should start from this body rather than from the three-lead one.

The pad is the output and it carries the load

On this package the exposed pad is pin 9 and it is connected to OUT. That is unusual among positive regulators and it changes the board rules. The copper under the part is at the regulated voltage, so it must be a separate island rather than part of the ground pour. The pad is the only thermal path, so it needs to be solid and stitched with vias to a matching island on the other side, but those vias are at the output potential and cannot land in a ground plane. And the 10 C/W junction to case figure is a solder joint number, not a package number: a part sitting on a minimal footprint runs closer to the 60 C/W ambient figure. At 1.87 W the difference is 93 C of rise against 112 C, which is the margin between a rail that survives a hot box and one that does not.

Stability, noise and the one capacitor that changes both

The part is stable with 2.2 uF of ceramic on the output, which is the family minimum and lower than most regulators of this current class. A capacitor from SET to ground, up to 1 uF, bypasses the SET resistor's noise and takes the output noise below the 40 uV RMS figure, at the cost of a start up time set by the resistor and capacitor product: 100 kOhm into 100 nF is 10 ms of time constant, and the rail takes a few multiples of that to settle. Ceramic capacitors with X5R and X7R dielectrics lose capacitance under DC bias, and the vendor explicitly warns that a 16 V 10 uF Y5V part can read 1 to 2 uF at 5 V, so the effective value at the operating voltage is what the stability calculation should use.

Ordering the MSOP body

The IMS8E code is tape and reel and shares its footprint with the E grade EMS8E. Between the two, the electrical table is the same and the difference is the guarantee: the I grade covers minus 40 C to 125 C by test, the E grade is tested at 25 C. Files that carry both are best kept on one cross reference, which is what the power management cross reference shows. Grade substitution in a shortage is worked on the BOM shortage recovery page, and the counting of one 1.1 A part against two smaller ones is on the component cost page.