Contact Us

LT3080EMS8E#TRPBF

Brand: Analog Devices
Analog Devices LT3080EMS8E#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080EMS8E#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080EMS8E#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080EMS8E#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080EMS8E#TRPBF: standard grade 1.1 A regulator in the 8-lead MSOP

The LT3080EMS8E#TRPBF is the E grade of the LT3080 in the 8-lead MSOP with an exposed pad, taped and reeled. The MSOP body sits between the SOT-223 and the DD-Pak thermally, at 60 C/W junction to ambient and 10 C/W junction to case, and it carries the tighter plus or minus 2 mV output offset that the DFN and MSOP share. The E suffix is the qualification rather than the silicon: tested at 25 C, guaranteed from 0 C to 125 C, cold end by characterization.

Published values

ParameterValue
Input voltage1.2 V to 36 V, VCONTROL separate
Output voltage0 V to 36 V, one resistor on SET
Output current1.1 A, 1.4 A typical current limit
SET pin current10 uA, 1 percent initial, 9.8 to 10.2 uA over temperature
VIN dropout350 mV at 1.1 A typical, 500 mV maximum
VCONTROL dropout1.35 V at 1.1 A typical
Output offsetplus or minus 2 mV
Minimum load300 uA typical, 1 mA maximum
Ripple rejection75 dB at 120 Hz, 55 dB at 10 kHz
Thermal resistance60 C/W junction to ambient, 10 C/W to case
Package8-lead MSOP, exposed pad is OUT, pin 9

The offset is the reason to pick this body over the SOT-223

Two millivolts against five is not a headline number, but it is the term that sets the ballast resistor when two regulators share a load. The sharing depends on the offset between the SET pin and the output, because that offset is what the ballast has to swamp. With 10 mOhm of copper trace per device, the vendor reports better than 80 percent current sharing, and a tighter offset makes that easier to hold over temperature. A 1.1 A rail that is really two 550 mA halves spreads the heat over two islands and halves the junction rise, which is how a small body gets to carry an amp in a warm box without a heat sink. Both SET pins and both IN pins tie together, and the outputs join through their ballast traces.

Start up, noise and the SET capacitor

The bare noise figure is 40 uV RMS from 10 Hz to 100 kHz, and the part is stable with 2.2 uF of ceramic on the output, which is a low minimum for this current class and a saving on board area. A capacitor across the SET resistor lowers the output noise and slows the start up: the vendor allows up to 1 uF, and the time constant is the resistor value times the capacitor, so 100 kOhm into 100 nF gives about 10 ms and the rail settles in a few multiples of that. On a rail that feeds a hot plug connector the slower ramp is often the point, because it keeps the inrush inside the upstream supply's limit. The trade is that a fast enable to full load sequence has to allow for the ramp.

Thermal headroom in a small body

At 60 C/W, 1.5 W of dissipation is 90 C of rise, so a 60 C ambient lands at 150 C and outside the 125 C limit. At 1 W the rise is 60 C and the same box lands at 120 C, which leaves 5 C. The practical limit for this body in a sealed enclosure is about 0.8 W, and the levers that move it are the input to output differential, the VCONTROL rail, or a second device in parallel. The 10 C/W junction to case figure shows what is available when the pad is properly soldered and stitched: most of the heat leaves through the board, so the island under the pad matters more than the package name.

Grade and sourcing

The EMS8E and IMS8E codes share a footprint and an electrical table, so a grade change in a shortage is a documentation change and the board does not move. Keeping both visible on one cross reference is what the power management cross reference does. Short lines are worked on the BOM shortage recovery page, and the trade between one wide body and two narrow ones is set out on the component cost page.