Contact Us

LT3065IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3065IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3065IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3065IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3065IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3065IDD#TRPBF: 500 mA industrial regulator in the 10-lead DFN

The LT3065IDD#TRPBF is the I grade of the LT3065 in the 10-lead 3 mm by 3 mm DFN on tape and reel, guaranteed from minus 40 C to 125 C at the junction. It is the same silicon as the MSOP code with the same 1.6 V to 45 V input range, 500 mA output, 0.6 V to 40 V adjustable output and programmable current limit. On a board it is the part that goes under a shield can or on the back side of a dense assembly, because the 3 mm body and the absence of leads buy about 2 mm of height over the MSOP and remove the lead coplanarity question entirely.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 2.2 V maximum at 500 mA
Output voltage0.6 V to 40 V, ADJ to OUT gives 0.6 V
Output current500 mA, external limit plus or minus 10 percent
Dropout voltage300 mV typical, 350 mV maximum at 500 mA
GND pin current270 uA at 10 mA, 1.8 mA at 100 mA, 11 mA at 500 mA
Output noise25 uV RMS with 10 nF on REF/BYP
ADJ bias current16 nA typical, 60 nA maximum
Reverse output current10 uA maximum at a 1.2 V output with the input at 0 V
Thermal resistance31 C/W junction to ambient, 9 C/W to case
Exposed padPin 11, ground, must be soldered
Grade and package10-lead 3 mm DFN, minus 40 C to 125 C

Assembly notes that decide yield

A DFN with an exposed pad has one failure mode that a leaded package does not: the pad is also the heat path and the ground return, so voids under it are both a thermal and an electrical defect. The datasheet asks for the pad to be soldered, and the practical requirements are a stencil aperture that delivers around 50 percent area coverage, a paste deposit that does not push the part off centre during reflow, and via holes that are either tented on the underside or plugged, because open vias wick paste away from the joint. Inspection is by X-ray rather than by eye. Once those are in place the package is unremarkable, and the 3 mm body with 0.5 mm pitch is comfortably inside standard assembly capability.

What 9 C/W to case means in practice

The junction to case figure is 9 C/W, which is worse than the 6 C/W of the 12-lead MSOP. The junction to ambient figure is 31 C/W against 28 C/W. Both differences point the same way: this is not a package you pick for thermal margin. At 1.5 W the rise is about 46 C and a 60 C ambient puts the junction at 106 C, which leaves 19 C to the 125 C limit and 44 C to the 150 C where lifetime starts to be derated. If a file needs more than about 1.6 W in the regulator, the honest options are a lower input differential, a second rail from a switching converter ahead of the linear part, or the MSOP body rather than a bigger copper pour.

Current limit as a protection rather than a guess

The IMAX pin is what separates this part from a fixed limit regulator. The external resistor sets the limit to plus or minus 10 percent over the full input and temperature range, which is a specification a protection circuit can be written against. With the pin grounded the internal limit applies at 520 mA minimum, and that figure folds back as the input to output differential grows, so the fault current into a shorted load falls as the voltage across the pass element rises. The consequence for a buyer is that the same order code can be used on a 200 mA sensor rail and a 495 mA logic rail, and the limit is set by a resistor rather than by stocking a second part number.

Ordering and substitution

The IDD code is tape and reel with the DFN footprint. Substituting the MSOP code is electrically transparent and mechanically impossible without a board change; substituting the E grade is mechanically transparent and changes the guarantee from minus 40 C to 0 C. Both cases come up in a shortage, and keeping the family on one cross reference is the cheapest way to see the options, which is what the power management cross reference does. Short lines are worked on the BOM shortage recovery page, and the arithmetic of grade and package substitution sits on the component cost page.