LT3060HTS8-5#TRPBF
Product Specifications
LT3060HTS8-5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3060HTS8-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3060HTS8-5#TRPBF: 5 V at 100 mA, tested to 150 C junction, ThinSOT
The LT3060HTS8-5#TRPBF is the 5 V fixed LT3060 in the 8-lead ThinSOT, tape and reel, in the H grade: tested at 150 C junction and guaranteed from minus 40 C to 150 C. Input range is 1.6 V to 45 V, output current is 100 mA, dropout is 300 mV typical, and quiescent current is 40 uA. It exists for boards where the ambient is high enough that a 125 C junction part has no margin left, which in practice means equipment in a sealed enclosure, near a power stage, or in a cabinet that bakes in the sun.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.6 V to 45 V, 50 V absolute maximum |
| Output voltage | 5 V fixed, 4.875 V to 5.100 V over temperature, H grade |
| Line regulation | 1.5 mV typical, 25 mV maximum, H grade |
| Load regulation | 3.7 mV typical, 75 mV maximum, H grade |
| Output current | 100 mA, current limit with foldback |
| Quiescent current | 40 uA typical at no load, below 1 uA in shutdown |
| Dropout voltage | 300 mV typical at 100 mA |
| Package | 8-lead ThinSOT, part marking LTFWH |
| Thermal resistance | 57 C/W to 67 C/W junction to ambient, 25 C/W to case |
| Maximum junction | 150 C, thermal shutdown at about 165 C |
| Grade | H, minus 40 C to 150 C, tested at 150 C |
What changes on the H grade electrical table
The tolerance window widens, and the load and line regulation limits widen with it. The 5 V output is specified to 4.875 V on the low side against 4.900 V for the I grade, line regulation is allowed to reach 25 mV against 8.5 mV, and load regulation reaches 75 mV against 35 mV. Those are not worse silicon; they are the honest spread when the reference is specified to 150 C instead of 125 C. A 5 V rail feeding logic does not care. A 5 V rail that is also a reference for a measurement front end cares a great deal, and the right answer there is a separate reference rather than a tighter regulator grade, because no member of this family holds a reference grade tolerance at 150 C.
The 150 C rating is headroom, not an operating point
The datasheet states that operating lifetime is derated at junction temperatures above 125 C, so the H grade's extra 25 C is there for fault conditions and for hot spots rather than for steady state operation. The vendor's own worked example sets the tone: 0.513 W at 54 C/W gives a 27.8 C rise and ends at 112.8 C from an 85 C ambient, well below the limit, with the arithmetic shown rather than asserted. On this 5 V code from a 12 V rail at 100 mA the dissipation is 0.70 W, which is a 40 C rise at 57 C/W and a 125 C junction from an 85 C ambient. That is at the derating line with no margin, which is the case where the H grade is the right purchase and where the copper under the part has to be full size.
Sequencing and start-up in a hot box
The REF/BYP capacitor sets both noise and soft start, and it is discharged when the part is in shutdown, so every enable produces the same ramp regardless of how long the rail has been off. That consistency is worth more in a hot enclosure than in a cold one, because it removes the variation that comes from a capacitor that has been sitting at temperature. The shutdown pin is rated to plus or minus 50 V absolute and its threshold is inside a 3.3 V logic swing. Current limit folds back with input to output differential, so a fault at 24 V input does not hold full current in the pass element while the junction climbs.
Where the H grade sits in the line
The family has four grades on one die: E and I to 125 C junction, H and MP to 150 C with different cold ends, since H stops at minus 40 C and MP reaches minus 55 C. Choosing between H and MP is a cold start question, and choosing between I and H is a hot ambient question. Both comparisons are tabulated on the power management cross reference. The price effect of the grade step is worked through on the component cost page, and the second source position for these wide temperature linear parts is described on ADI part second source.