Contact Us

LT1763IDE-5#TRPBF

Brand: Analog Devices
Analog Devices LT1763IDE-5#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1763IDE-5#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT1763IDE-5#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1763IDE-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1763IDE-5#TRPBF: a 5 V post regulator that removes switching residue from an analogue rail

What this order code is

LT1763IDE-5#TRPBF is the 5 V fixed member of the LT1763 family in the 12 lead 4 mm by 3 mm DFN, industrial grade, lead free and on tape and reel. It delivers 500 mA with 300 mV of dropout, draws 30 microamps, and with a 0.01 microfarad bypass capacitor on the BYP pin it reaches 20 microvolts RMS of output noise over 10 Hz to 100 kHz. The fixed output means no divider, no divider current and no resistor tolerance in the error budget. Reverse battery protection, reverse current protection, current limit and thermal limit are internal, and the family needs no external protection diode.

This part is almost never used as a first stage. A 5 V output from a 12 V input at 500 mA dissipates 3.5 W, which the package cannot pass, so the 5 V member is used where the input is already close: a 6 V rail, a 5.5 V intermediate bus, or the output of a switching converter that has to be cleaned up. In the last case the linear regulator is being bought for its noise and its rejection, not for its efficiency.

Parameters as published

ItemValue
Output voltage5 V fixed
Output current500 mA
Dropout at 500 mA300 mV
Minimum usable input at full load5.3 V
Input range1.8 V to 20 V
Quiescent current30 microamps, controlled in dropout
Shutdown currentunder 1 microamp
Output noise20 microvolts RMS with a 0.01 microfarad bypass capacitor
Minimum output capacitor3.3 microfarads
Protectionreverse battery, reverse current, current and thermal limit
Body12 lead DFN, 4 mm by 3 mm, 0.75 mm high
Temperature gradeindustrial
Packingtape and reel, lead free

Numbers that decide the application

The power budget is a straight line: at 5 V out the dissipation is 1 V times the current from a 6 V input, 2 V from 7 V, and 7 V from 12 V. From 6 V at 500 mA it is 0.5 W and the DFN handles it; from 6 V at 300 mA it is 0.3 W. The usable ceiling for this body is around 1 W with a good pad, which at 5 V means a 6 V input at 500 mA or a 12 V input at about 140 mA. Any application that needs 5 V at 1 A from 12 V is a switching converter with a linear post stage, not a single linear part.

As a post regulator the relevant figure is the rejection of the switching residue, and the part is specified for low output noise rather than with a headline rejection number. What can be stated from the published data is the noise floor: 20 microvolts RMS over the full audio band, which at 5 V full scale is 0.26 of a 16 bit least significant bit. The switching converter in front has to leave less than a few tens of millivolts of residue for that to hold, because a linear regulator rejects at a rate that falls with frequency and the switching fundamental sits where the rejection is weakest. The usual arrangement is a 300 kHz to 500 kHz converter, a small inductor and a 10 microfarad ceramic, then this part with its 3.3 microfarad output capacitor.

Dropout sets the minimum intermediate bus voltage. At 500 mA the part needs 5.3 V, so an intermediate bus specified at 5.5 V leaves only 200 mV of margin for the converter tolerance and the load transient, which is tight. A 6 V intermediate bus is the comfortable choice: it leaves 700 mV, which covers a plus or minus 5 percent converter and a load step without entering dropout. That is also why the 5 V member often appears with a 6 V or 5.5 V rather than a 5.2 V upstream rail.

The 3.3 microfarad minimum output capacitor is a stability requirement, and the effective capacitance of a ceramic part falls with dc bias, so a 4.7 microfarad 10 V X5R at 5 V dc bias may be near the limit. A 10 microfarad part or a higher voltage rating in the same case size is the safe choice on this rail.

Where it fits and where it does not

It fits a cleaned 5 V analogue rail behind a buck, a 6 V bus regulator, and any board where a 5 V sensor or reference supply has to be quiet rather than efficient. It does not fit a 12 V input at high current, a 5 V input, or a rail that has to start below 5.3 V at full load. It also does not replace a switching converter on a thermal basis: the 3.5 W that a 12 V input would put into the package is larger than most enclosures can remove from a 4 mm by 3 mm body.

Supply and second source questions

The questions that come back on this code are about the input rail, the noise with and without the bypass capacitor, and the grade. The fixed 5 V output also exists in the SO 8 lead body and in other temperature grades, and those differ in thermal path and in the temperature guarantee while sharing the electrical table. The members that share the die and the ones that only look similar are listed on the power management cross reference page.

Sourcing notes and next step

We quote this code against the bill of materials and check the four fields that decide whether the line runs: output voltage, grade, body and reel. Where the exact code is short we will say so rather than offer a switching converter as a substitute for a linear post regulator, because the noise is the reason the part is on the board. Send the line items, quantities and required date through the BOM shortage recovery page, and where the rail is being reworked around a shorter part, the drop in replacement check sheet covers the dropout, the capacitor stability and the bypass pin that a voltage and current comparison misses. The family list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty