Contact Us

LT1761IS5-BYP#TRPBF

Brand: Analog Devices
Analog Devices LT1761IS5-BYP#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1761IS5-BYP#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT1761IS5-BYP#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1761IS5-BYP#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1761IS5-BYP#TRPBF: the I grade bypass code, and the capacitor that carries the noise claim

What this order code is

LT1761IS5-BYP#TRPBF is the adjustable LT1761 with the bypass pin brought out, I grade, in the 5-lead TSOT-23 body on a lead free reel. The output is set by an external divider from a 1.22 V reference, the input runs from 1.8 V to 20 V, the load is 100 mA, the dropout is 300 mV at that current and the quiescent current is 20 uA.

This code sits at the intersection of two decisions. The bypass pin is what allows the 20 uV RMS noise figure to exist at all, and the I letter is what puts a guaranteed limit on the part across the industrial temperature span. A buyer who needs both and orders either of the other two options gets one of them and not the other, which is the most common way this family is mis-specified.

Parameters as published

ItemValue
Configurationadjustable from a 1.22 V reference
Output range1.22 V to 20 V
Output current100 mA
Input voltage range1.8 V to 20 V
Dropout at 100 mA300 mV
Output noise with 0.01 uF on BYP20 uV RMS, 10 Hz to 100 kHz
Quiescent current20 uA
Shutdown pinnot present on this code
Output capacitor1 uF ceramic
Body5-lead TSOT-23
GradeI
Packingreel, lead free

Numbers that decide the application

The noise claim belongs to the capacitor. With 0.01 uF on the bypass pin the family publishes 20 uV RMS over 10 Hz to 100 kHz; without it the reference noise passes to the output unfiltered and the number is larger, which is why every comparison has to state whether the capacitor was fitted. Ceramic dielectric matters at temperature: an X5R or Y5V part loses most of its capacitance at 85 C, and the corner of the filter moves with it, so an X7R or a C0G part is the one to specify on a board that has to be quiet when warm. The leakage of the capacitor sits on the reference node, and a 1 uF part with a few microamps of leakage is a different circuit from a 0.01 uF part with nanoamps.

The divider sets the output and its tolerance adds to the reference tolerance. One percent resistors contribute about 1.4 percent, which is 46 mV on a 3.3 V output and 0.1 percent parts reduce that to 4.6 mV. The feedback pin bias has to be small against the divider current for the same reason, and the divider current itself is a load on the 20 uA quiescent budget, so a 10 kohm divider drawing 122 uA at a 1.22 V reference is four times the regulator current and defeats the reason for a micropower part. The usual compromise is a few hundred kilo ohms with a 1 uF feed forward capacitor across the top resistor.

At 100 mA the dropout of 300 mV is 3 ohm, so the minimum input is the output plus 0.3 V and the dissipation is the input minus output times the load. From 5 V to 3.3 V that is 0.17 W and a rise near 42 C; from 12 V to 3.3 V it is 0.87 W, which the 5-lead body cannot pass at 100 mA and can pass at 20 mA. The I grade changes none of this arithmetic, it changes the guaranteed limits at the top of the range.

Where it fits and where it does not

It fits a quiet analog rail that has to stay on, an ADC reference buffer, a VCO or PLL supply and a low current sensor front end in equipment that runs hot, because it is the only 5-lead code in the family that offers both the bypass pin and the industrial grade. It does not fit a rail that has to be switched off, it does not fit a load above 100 mA and it does not fit a 24 V bus.

Supply and second source questions

A substitute has to match four fields: 1.22 V adjustable, bypass pin on the package, I grade and the 5-lead TSOT-23 body. Parts that match the first and the fourth and miss the second will regulate and will not meet the noise line, and parts that miss the third will regulate at 25 C and lose their guarantee at 105 C. The regulator families and their pin options are listed on the power management cross reference page.

Sourcing notes and next step

We quote the grade letter and the pin function together, because on this family they are the two fields that a short line item loses first. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability and with the grade on the reel. The wider regulator list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty