LT1716IS5#TRPBF
Product Specifications
LT1716IS5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1716IS5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT1716IS5: a 44 V comparator that runs on 35 microamps
The LT1716IS5 is a micropower precision comparator in a 5-lead TSOT-23, operating from any total supply between 2.7 V and 44 V and drawing 35 microamps of quiescent current. The input stage is the unusual part: it uses an over-the-top structure that allows the common mode range to extend 44 V above the negative supply independently of the positive supply, and the inputs survive 44 V both differential and common mode. The output swings to within 35 millivolts of the negative rail and 55 millivolts of the positive one, and it can drive a load connected to a supply higher than its own.
Published values
| Parameter | Value |
|---|---|
| Supply range | 2.7 V to 44 V total |
| Quiescent current | 35 microamps |
| Input offset voltage | 1.5 millivolts maximum |
| Input common mode range | 44 V above the negative supply, independent of the positive supply |
| Differential input | 44 V |
| Output swing | within 35 millivolts of the negative rail, 55 millivolts of the positive rail |
| Output pull-up | internal current source, no external resistor |
| Output load supply | may be higher than the comparator supply |
| Package | 5-lead SOT-23, 1 mm profile |
| Temperature | specified from minus 40 to 85 degrees for the I grade |
| Qualification | AEC-Q100 for automotive applications |
A 44 V input on a 3 V supply, which is the whole point
A conventional comparator with a 3.3 V supply cannot look at a 24 V rail, and the usual workaround is a resistor divider. A divider costs accuracy through the resistor tolerance, loads the rail being monitored, and adds a pole that slows the response to a fast transient. The over-the-top input stage removes the divider: the input can sit 44 V above the negative supply while the comparator itself runs from 3.3 V, and the output still swings to the logic level the microcontroller expects.
The limit that catches people is that the input range is referenced to the negative supply, not to the positive one. In a single supply system with the negative pin at ground, that means the input can go to 44 V regardless of the 3.3 V rail. In a split supply system the 44 V sits on top of the negative rail, so the usable range moves with it.
35 microamps is what makes a permanent monitor possible
A comparator that draws 35 microamps can be left powered from a battery for years. At 12 V that is 0.42 mW, which against a 2000 milliampere hour cell is a self discharge term rather than a load. That is the reason this part appears in lamp monitors, relay drivers and supply supervisors that have to be alive while the rest of the product is asleep.
The internal pull-up current source removes the external resistor that an open collector output would need, and that resistance is usually the largest single term in the power budget of a micropower comparator circuit. Removing it also removes the trade between pull-up strength and rise time, because the current source is set by the part rather than by the board.
Low supply, high side load
The output stage can drive a load connected to a supply above the comparator's own rail, the same way an open collector output can. In practice that means a 3.3 V comparator switching a 24 V relay coil through an external transistor, or driving a gate whose source sits at a higher potential than the logic supply. The limit is the output device's voltage rating rather than the comparator's supply.
The internal pull-up is a current source into the output node, so the rise time into a capacitive load is set by the current and the capacitance. A 100 picofarad load with tens of microamps of pull-up is a rise time measured in tens of microseconds, which is fine for a supply monitor and useless for a pulse circuit. Where speed matters, the external pull-down or a different output arrangement is what changes it, not the supply voltage.
Where a customer needs a second position on this part, the power management cross reference is the starting point, component lead time solutions sets out the checks a substitution has to pass, and vendor consolidation is the short lead time route we quote against.
Two questions buyers ask
Can the input sit at 24 V while the comparator runs from 3.3 V? Yes, that is what the over-the-top input stage is for. The common mode range extends 44 V above the negative supply independently of the positive supply, so a 24 V rail can be monitored directly with no divider.
Is the 35 microamp figure the total supply current? It is the quiescent current of the comparator itself. The output current into the load and any external divider current come on top, which is one reason the internal pull-up and the over-the-top input are worth having together.