LT1716CS5#TRPBF
Product Specifications
LT1716CS5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1716CS5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT1716CS5: the commercial grade is also minus 40 to 85, not zero to seventy
The LT1716CS5 is the commercial grade of the 44 V micropower comparator in a 5-lead TSOT-23. The order table gives it minus 40 to 85 degrees, which is the same range as the industrial grade and is the detail that a part number comparison based on the letter usually gets wrong. The electrical behaviour is shared with the rest of the family: 2.7 V to 44 V supply, 35 microamps of quiescent current, 1.5 millivolts of maximum offset, an over-the-top input that reaches 44 V above the negative supply, and an output that swings close to both rails and can drive a load above its own supply.
Published values
| Parameter | Value |
|---|---|
| Supply range | 2.7 V to 44 V total |
| Quiescent current | 35 microamps |
| Input offset voltage | 1.5 millivolts maximum |
| Input common mode range | 44 V above the negative supply |
| Differential input range | 44 V |
| Output swing | within 35 millivolts of the negative rail, 55 millivolts of the positive rail |
| Output pull-up | internal current source |
| Package | 5-lead SOT-23 |
| Temperature | specified from minus 40 to 85 degrees |
| Wide temperature option | the H grade is specified from minus 40 to 125 degrees |
| Qualification | AEC-Q100 for automotive applications |
Choosing between C and I when the range is the same
The order table lists the C and the I grade over the same minus 40 to 85 degrees, so the letter does not describe a wider or narrower range in this part. That is unusual enough that it is worth checking on the datasheet rather than assuming the usual convention, because a substitution in the other direction, taking a part whose commercial grade really is zero to seventy, would put the circuit outside its specified range in a cold store or an outdoor enclosure.
The difference between the two grades is in the guarantee, and for a comparator used as a supply monitor the practical question is whether the 1.5 millivolt offset limit has to hold at both temperature extremes. In a monitor with 100 millivolts of hysteresis, 1.5 millivolts is not the limiting term; in a precision threshold detector it is.
A monitor that has to work at 44 V and at 3 V
The over-the-top input means the same circuit can watch a 44 V rail with the comparator powered from 3.3 V, and it means the input can be taken to 44 V while the supply is only 2.7 V. In a system that has a high voltage rail and a low voltage logic rail, that removes the divider, the divider current and the divider tolerance from the measurement.
The input bias current is the term that remains. It flows out of the input when the input is above the supply, and through any source resistance it produces an offset. A high impedance divider on the input, added out of habit, is exactly the wrong thing to put in front of this part, because the bias current multiplied by a few hundred kilohm is larger than the 1.5 millivolt offset the part is specified for.
Where the 35 microamps goes at the extremes
At 44 V and 35 microamps the part dissipates 1.5 mW, which a 5-lead TSOT-23 removes without noticing. At 2.7 V and 35 microamps it dissipates 0.1 mW. The supply current is nearly flat across the range, which is unusual for a comparator and is what makes the part usable on a rail that swings widely, such as an unregulated battery rail that starts at 12 V and ends at 3 V.
The output stage adds to that, and it is the part of the budget that gets forgotten. Driving a load connected to a higher supply means the output current flows from that supply through the part, and at a few milliamps that is larger than the entire quiescent current. The 35 microamps describes the comparator, not the interface it drives.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use one stop BOM sourcing to confirm a substitute before it is fitted; component obsolescence management is the routine for a part that has already stopped shipping.
Two questions buyers ask
Is the C grade really specified to minus 40 degrees? Yes. The order table gives the C and I grades the same minus 40 to 85 degrees. For a wider range the H grade is specified from minus 40 to 125 degrees, not the C or I grade.
Does the input need a series resistor at 44 V? The inputs are rated for 44 V both differential and common mode, and the part is specified that way without an external series resistor. Adding a high value resistor in front of the input introduces an offset through the input bias current that can exceed the offset voltage specification.