Contact Us

HMC939ALP4E

Brand: Analog Devices
Analog Devices HMC939ALP4E is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC939ALP4E — Analog & Mixed-Signal ICs | Superb Automation

HMC939ALP4E

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC939ALP4E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC939A: 31 dB in 1 dB Steps to 33 GHz, and the Negative Rail Is Not Optional

The HMC939A is a five bit gallium arsenide digital attenuator covering 0.1 GHz to 33 GHz, with 1 dB steps to a total of 31 dB, a typical step error of 0.4 dB and an input third order intercept of +43 dBm. It has five control inputs that swing between 0 V and +5 V, and it needs a negative supply as well, because the RF path itself is biased below ground. That combination, positive logic and a negative rail, is the detail that most first articles get wrong: the attenuator switches state perfectly with only the +5 V applied, and then fails the loss and linearity tests.

The loss budget at the top of the band

ParameterValueEffect
Frequency range0.1 GHz to 33 GHzOne part covers microwave and the low millimetre wave band
Attenuation range31 dB in 1 dB stepsFive bits, 32 states
Insertion loss to 18 GHz4.0 dB typical, 5.5 dB maximumPaid before any attenuation is applied
Insertion loss 26.5 to 33 GHz6.5 dB typical, 8.5 dB maximumMore than the first six bits of attenuation at the band edge
Input intercept+43 dBmAllows the attenuator to sit after a driver stage
Control and suppliesFive lines at 0 V or +5 V, plus -5 VSix wires, two rails
Switching60 ns rise and fall, 90 ns on and offLimits how fast an automatic gain loop can step

Insertion loss grows faster than the attenuation does

Across the band the insertion loss roughly doubles, from 4 dB to 6.5 dB typical, while the attenuation range stays at 31 dB. A link budget built at 10 GHz and applied at 30 GHz will be 2.5 dB short, and because the loss sits ahead of the attenuation, the dynamic range of the stage behind the attenuator shrinks by the same amount. Where the attenuator is used to protect a receiver, the protection is 2.5 dB weaker at the top of the band than the calculation suggests.

Why a negative supply on a positive control part

The control interface is positive and simple: five lines, 0 V for one state and +5 V for the other, which a CMOS driver can produce directly. The RF path needs the negative rail, and the current drawn from it is small, a few milliamps, but the rail has to be quiet. Ripple on the negative rail couples into the attenuator through the same mechanism that gives the part its linearity, so a charge pump without a post regulator will add spurs that no amount of filtering on the positive rail will remove.

Five bits is not always thirty two useful states

Because the steps are binary weighted, the worst case transition is not a single step but a combination: going from all bits on to all bits off changes 31 dB in one control update. In a gain loop that has to track a fading signal, the loop should be written to move one bit at a time, or the transient will be 31 dB rather than 1 dB. The 90 ns switching time is fast enough that the transient is short, but the settling of whatever follows the attenuator is usually slower.

Replacement notes

A substitute has to match the band, the step size and the logic polarity, and a part with negative logic control in a positive logic socket will read as a 31 dB pad rather than an attenuator. The RF component sourcing page lists the attenuator family, the pin to pin cross reference page covers control and footprint differences, and the incoming inspection plan describes the attenuation check performed on receipt.